similar to: CallerID on Indian PSTN is not working.

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

Hello, Is it possible to set a variable in dialpan when the someone calls a particular DID number so that i can use that variable for calls coming to that number only. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100819/25402ade/attachment.htm

I have a SIP trunk from my Asterisk server to an Avaya CM server. If I place calls inbound, everything works fine. If I place calls outbound, originating from the Asterisk box, everything works fine (I have done this with the use of the .call files). If I setup an extension with the findme-followme feature and have it try to hair-pin a call back out the same trunk to the Avaya, I get a

I have two servers, each connected to the PTSN via PRI. When I call from site A (951-999-9999) to site B (555-1212) and the phone at site B is on the phone, I hear the normal ring tone for about 20 seconds, then the message "all circuits are busy now. please try your call again latter" followed by the congestion tone. Instead, I want this to busy ring and then hang up without any

Hi, I purchased a G.729 1 channel codec license from digium. And installed as per the documentation. Then configured the sip.conf to use the new codec. For that, I am added the following entries in sip.conf (via web interface, as i am using asterisknow 1.5) disallow=all allow=g729 allow=ulaw allow=alaw allow=gsm After that, when try to call through the PSTN line I can hear the voice of

Hi All, I am trying to connect my asterisk box with freepbx to PSTN. I have purchased x100p FXO card and installed in my asterisk server. My freepbx detected the x100p FXO card and i can see the card specific details in command line. I have configured the following things. 1. OUTBOUND caller id and Dialing rules in Freepbx. 2. INBOUND route When i call to the PSTN number before

Does anyone know why? ThePBX*CLI> -- Executing [310-456-7890 at from-trunk:1] Set("SIP/202.101.202.101-b763ce60", "__FROM_DID=310-456-7890") in new stack -- Executing [310-456-7890 at from-trunk:2] ExecIf("SIP/202.101.202.101-b763ce60", "1 |Set|CALLERID(name)=310-456-0987") in new stack -- Executing [310-456-7890 at from-trunk:3]

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hello everyone, I am facing a strange problem on my asterisk box (using isdn lines with pri card installed on it). Normal incoming/outgoing calls are working perfectly fine. When a user dial a wrong/out-of-service number they don't hear back any such message like "The number is wrong or user is switched off" in some cases, and it's just a silence for the user. Now while

Hello, we have an asterisk (1.4.21.2) with ZAP and mISDN channels, the mISDN are 2 incoming GSM Modems, each with 2 simcards. No, the mISDN line one and two are fine, but when I get a call on line 3 something with the time is wrong. Timeconditions fall through to off-hours even if the time of the call is clearly inside business hours, here a log excerpt: [Aug 26 11:04:36] VERBOSE[3112]

I have two internal analogue extensions off a TDM400P. If the first is busy, I'd like to ring the second. So: [incoming] exten =>s,1,Answer() exten =>s,n,Dial(${mainline},60) exten =>s,n,ExecIf($["${DIALSTATUS}" = "BUSY"]?Dial(${secondline},30)) But it doesn't work because * first tries Call Waiting on the main line. Here I dial out: -- Starting

I'm having a problem receiving incoming faxes and I'm hoping someone here can help me out. My system is a PBX in a Flash with one dahdi card for my incoming analog lines and another dahdi card for my analog devices (fax and modem). My dahdi-channels.conf file looks like: ; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 23 14:56:24 2009 ; If you edit this file and execute

Hi: I am useing asterisk 11.12. I use G722 as preferred codec for my ip-phone. and my PSTN DAHDI use alaw. G722 is great when ip-phone talks to each other. but when ip-phone dialout to PSTN DAHDI, G722 is not great, since it is need to transcode to alaw. so I try to change the codec when dial from SIP to DAHDI. I tried to use IP_CODEC/SIP_CODEC_OUTBOUND at dialplan. but the SIP

Hi list! I have this configuration for sending T38 faxes to my T38 fax termination provider: T38modem --> hylafax --> Asterisk-SIP-Extension --> T38 termination provider --> T.30 termination to PSTN We are experiencing 2 problems with this (if you want configuration files, it won't be a problem, just tell me): 1. T38 termination provider receives faxes at 2400 bpps from our

Hi people, I have a problem with some extensions. The calls are ended after 31/35 seconds, also, it depends on the number which I call. This is the log, but I've not been able to find something wrong... Any ideas? [Jun 11 15:50:46] DEBUG[26071] app_macro.c: Executed application: ExecIf [Jun 11 15:50:46] VERBOSE[26071] logger.c: -- Executing [s at macro-dialout-trunk:16]

My Asterisk 1.2.40 process crashes regularly in the is_zero_or_null function at: return (*vp->u.s == 0 || (to_integer (vp) && vp->u.i == 0)); My gdb trace is at: http://pastebin.com/raw.php?i=hmhzZxye Other examples here: http://lists.digium.com/pipermail/asterisk-users/2010-March/245927.html Can anyone please help?

Hi, I've run into a minor snag trying to pass on CALLERID presence from one Asterisk to another via SIP (both running 13.16.0) I have a PRI coming in PBX_A and PBX_A is connected to PBX_B via SIP. PBX_A gets PRI calls on a 4 port Digium card, and each call naturally has its own callerid values and presence. I pass on those calls to PBX_B via SI, and I'm trying to pass on this

We use asterisk 1.6 with DAHDI and a PRI ISDN 30 line in the Netherlands. Can anyone help me sorting out this issue?? Thanks in advance! -- Executing [s at macro-transfer:25] NoOp("SIP/joostkuif-00000003", "gehe= im") in new stack -- Executing [s at macro-transfer:26] NoOp("SIP/joostkuif-00000003", "voor= de SET CALLERPRES() =3D

We use asterisk 1.6 with DAHDI and a PRI ISDN 30 line in the Netherlands. Can anyone help me sorting out this issue?? Thanks in advance! -- Executing [s at macro-transfer:25] NoOp("SIP/joostkuif-00000003", "gehe= im") in new stack -- Executing [s at macro-transfer:26] NoOp("SIP/joostkuif-00000003", "voor= de SET CALLERPRES() =3D