similar to: Dahdi install issues

dahdi built fine on 5.1.20, but on 5.2.7: ............. CC [M] /home/asterisk/rpmbuild/BUILD/linux-dade6ac/drivers/dahdi/vpmadt032_loader/dahdi_vpmadt032_loader.o SHIPPED /home/asterisk/rpmbuild/BUILD/linux-dade6ac/drivers/dahdi/vpmadt032_loader/vpmadt032_x86_64.o LD [M] /home/asterisk/rpmbuild/BUILD/linux-dade6ac/drivers/dahdi/dahdi_vpmadt032_loader.o Building modules, stage 2.

but I need to apply this patch to the tar file in the dahdi-linux-2.2.0.2-1= _centos5.src.rpm and rebuild it, but that , `dahdi-linux` pulls in: dahdi-firmware dahdi-firmware-oct6114-064 dahdi-firmware-oct6114-128 dahdi-firmware-tc400m kmod-dahdi-linux kmod-dahdi-linux-fwload- yum-kmod That of which contain dahdi-firmware and kmod-dahdi-linux-fwload-vpmadt032 = which don't have srpms

I updated an AsteriskNow system to 2.6.18-194.26.1.el5 with yum update. Upon reboot dahdi modules cannot be found. In yum.log I see that kmod-mISDN, kmod-dahdi-linux and kmod-dahdi-linux-fwload-vpmadt032 were all deleted during the update. I reinstalled the deleted packages but the dahdi modules can still not be found. They do seem to be under /lib/modules/2.6.18-194.17.4.el5, but no for the

Hello, I'm writing here hoping to have a hint from Asterisk/Digium packager maintainer, Jason Parker (of course that any other's opinion is welcomed). We have installed an asterisk machine using Asterisk and Digium repos. Unfortunately we have found that an Astribank could not be connected due to the lack of the firmware files May 18 14:19:22 tenora1 kernel: usb 1-6: new high speed USB

Is it possible to get .spec or .src.rpms for packages on packages.digium.com? I specifically need to rebuild kmod-dahdi-linux-fwload-vpmadt032 for the kernels available in CentOS 5.10. I see there?s source at downloads.digium.com/pub/telephony/firmware/releases, but .spec files are not included. -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc

Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI

Hi: I?Bought TDM2400P ,with 24 FXO ports , I installed? the asterisk 1.4.28 and?dahdi 2.2.0?and then i compiled them and configured all, i pluged into 8 pstn line into the Rj connector and then i got messages on asterisk console that alarm cleared on channels 1->8??, at this step everything should go fine ,but when i try to make a call?through the TDM?there is silence and no audio,and then i

Been trying to get this to go but nongo :-). I'm asking for some guidance especially if I should not be doing this on an RT kernel. I've installed what is supposed to be all of the requred deps. Some factors that may be adding to my problem are: 1. this is only a test.. it's a 32bit guest OS running in VMware under a 64 bit windows host.. (although I'be compiled it on other

Dear asterisk users, We want setup TE121 digium board: Model: Digium TE121: VoiceBus technology allows the TE121 to use an industry standard bus-mastering PCI Express interface. http://www.digium.com/en/products/digital/te121.php My platform Server: HP Proliant 150 G5 OS: UBUNTU x86_64 GNU/Linux Asterisk: 1.4.21.2 zaptel: SVN-branch-1.4-r4662M When we enable zaptel driver for TE121, the

Just finished installing Kernel 3.0.0 and tried to compile DAHDI Complete 2.4.1.2+2.4.1. Errors below: ________ /home/doug/Extracts/dahdi-linux-complete-2.4.1.2+2.4.1/linux/drivers/dahdi/dahdi-base.c:95:2: warning: #warning "No CONFIG_BKL is an experimental configuration." CC [M]

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

Errors follow: make make -C linux all make[1]: Entering directory `/usr/local/src/asterisk/dahdi-linux-complete-2.4.1.2+2.4.1/linux' make -C drivers/dahdi/firmware firmware-loaders make[2]: Entering directory `/usr/local/src/asterisk/dahdi-linux-complete-2.4.1.2+2.4.1/linux/drivers/dahdi/firmware' make[2]: Leaving directory

Hi, Just trying to figure out / solve some echo issues with one of our systems. The server is a Dell R710 running Asterisk 1.6.x and Dahdi 2.2.x The card in the server is a TE121P (with VPMADT032 echo canceller) We are experiencing some weird echo issues with our Cisco 79xx phones, only when we are dialing out via the PRI. The echo is like a side tone, where we can hear ourselves speaking. The

The Asterisk.org development team has released Zaptel versions 1.2.24 and 1.4.9. Zaptel 1.2.24 Highlights * Linux kernel 2.6.24 compatibility * New module parameters for tuning VPMADT032 echo canceller modules * Improved interrupt handling in the wcte12xp driver Zaptel 1.4.9 Highlights * Linux kernel 2.6.24 compatibility * New module parameters for tuning VPMADT032 echo canceller modules *

The Asterisk.org development team has released Zaptel versions 1.2.24 and 1.4.9. Zaptel 1.2.24 Highlights * Linux kernel 2.6.24 compatibility * New module parameters for tuning VPMADT032 echo canceller modules * Improved interrupt handling in the wcte12xp driver Zaptel 1.4.9 Highlights * Linux kernel 2.6.24 compatibility * New module parameters for tuning VPMADT032 echo canceller modules *

Hi pals, Pardon me if this question sound basic please. This is the first installation where I have to use the analogue card and therefore a little lusty. I have googled a lot, but though there is a lot of information about the above file, none indicate where the file lives. I have a installed asterisk and zaptel software on a fresh installation of CentOS 5. This all from source and following

Hi How can i know the version of my vpmadt032 firmware? Thanks Ruben

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2-rc1 DAHDI-Tools-v2.9.2-rc1 dahdi-linux-complete-2.9.2-rc1+2.9.2-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete This release is

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2-rc1 DAHDI-Tools-v2.9.2-rc1 dahdi-linux-complete-2.9.2-rc1+2.9.2-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete This release is