similar to: E1 R2 Congestion Status

Hi, I have a digium card (igium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02)) 4 ports I want to make a loop test between digium card E1 to test the configuration of dahdi What I want to do scenario is I connect port 1 and port4 in the digium card with E1 cable SIPcall-->E1 Digium port 1--->(Loop)E1 port 2---->sip extension local. kindly can any can help me to

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Hello to all I'm using asterisk 1.4 and dahdi. I had everything working fine, and I could place calls through my R2 channel. But now the channel is always "RED" and Im getting this error message: TE4XXP: Version Synchronization Error! Here is my chan_dahdi.conf------------------------------ [channels] language=en context=incomingr2 signalling=mfcr2 mfcr2_variant=ar

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Hello Team I have installed the new DL580 and used the new TE420B to add capacity on our ivr. Before I put new E1?s I decided to first move the old e1 from the old system to this new one but it has errors which not only affect the audio quality, but also cause the asterisk to refuse any call after sometime even though the channels seems up and active {seems d-channel fails}.. When processing

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Dear All I installed a Digium card TE405P with zaptel and its running successfully with no alarms, but asterisk is not running . Any one have a cure or advice 03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02) Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2 Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi, I am having issues sending and receiving fax on my asterisk setup. Currently I have a server that has 2 x E1 TDM cards one is sangoma and the other one is openvox. Both support echo cancellation. One of the e1 is connected to our telco provider via mfcr2 where all our incoming calls originate. On the other end is a pri connection going to HICOM PABX where the local attached to a fax is

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hi, would be glad to be contributing with this question to all the comunity. I?m having a weird issue, suddenly I get channels on IDLE 0x00 state until I do a dahdi restart. Trying to do a call trace to see whats going on deeper, I get surprised when tried to open the .call file to see the log this is incomplete. This is what I see [root at localhost telefonica]# nano

hello list i have installed 2 diguim card in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi list, I'm trying to setup an asterisk 1.8.0 with MFC/R2, but I'm having these error messages loading chan_dahdi: > module load chan_dahdi.so ERROR[9241]: chan_dahdi.c:11848 mkintf: Signalling requested on channel 1 is MFC/R2 but line is in ISDN PRI signalling ERROR[9241]: chan_dahdi.c:16180 build_channels: Unable to register channel '1-15' I got the config in

HelloI have the following system Asterisk 1.6.1dahdi 2.2.0.2 TE420P card Centos I have noticed that all the four lights are blinking(ie coming red and then off so on)... Previously I also noted that when dahdi drivers are not installed lights blink but one by one in sequence(like in marriage cermonies :P) and after dahdi installation lights get off ... but this time all at same time

Dears What's the major deference between Asterisk 1.6.0.6 and Asterisk 1.4.23 Regards Khaled Chehab NGN Eng. Untitled Operations Office - Lebanon Office : +961 1 868686 ext 115 Mobile: +961 3 045212 E-mail: <mailto:bsara at mg-tel.com> Kchehab at Xplorium.com MSN ID :KhalidChehab at hotmail.com Web Site:

Questions: Does anyone have a really STABLE asterisk system running about one year without need to restart the service or the SERVER ? Does anyone have a production Call Centre saled that don't lockup and is stable for 6 months ? I'm asking this questions because we have choose Asterisk for our call centre solution but, since the bugtracker only grows and people still want to stuck more

I installed asterisk 1.4.4 final ,but the cdr is not written any patch or tweaking can be done Regards ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by e-mail without express written confirmation by an officer of Xplorium. Any views expressed by an individual in this