similar to: Sangoma card reports HDLC errors

Hi all, as good? I try to install asterisk-1.2.14, zaptel-1.2.12,libpri-1.2.4,addons-1.2.5 , sounds-1.2.1 and wanpipe-2.3.4-3 and hwec-utils-beta4-2.3.4 But it is not compiling drivers of the Sangoma, why udev's for board in "/dev/zap"(1-31, channel,ctl,pseudo,timer) is not created. But when I install a board TE110P Digium, udev's is created and asterisk functions perfectly. : )

My Sangoma Experience in Asterisk: Followup 2005-05-06 original review can be found at: http://astguiclient.sourceforge.net/Sangoma_experience.txt It's now been a month since I finished my last round of tests with the Sangoma A104u board in Asterisk. I have had a lot of conversations with the guys at Sangoma about how my system runs so that they could set up their test systems to try to

Hi, I am facing an audio-problem with the dial application and I (!) think, that it is connected to the dahdi parameter "overlapdial=yes". Sangoma support does not see any connection between this. But when enabling this option I face with some(!) dial-partners a audio one-way issue (the called party can not be heard). Only using PSTNS (germany e1 trunk) - no voip. Is there any

I'm trying to install wanpipe on my new 2.6.21-2-amd64 core 2 duo machine (Debian's amd64 works with EMT64 too) to run Asterisk. I'm getting compilation errors when trying to install the wanpipe utilities. We are intending to use a Sangoma A102 card for ISDN30 in the UK. I've tried both the current stable 2.3.4-10 release and the new wanpipe-3.1.3 beta release of wanpipe. The

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hello, Several people asked to get a hold of the stats I used to determine that the Sangoma T1/E1 boards performed better in our real-world tests than the Digium boards. We've decided to post our results after confirming them over the past month of operations. Here is a link to the last two reviews I wrote about Sangoma with Asterisk:

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi List, Just a little question about a notice from asterisk I don't understand: Here is what I have as soon as I place a call on a E1 line with an a104D Sangoma Card ( asterisk 1.2.9.1 ) : Jun 26 18:57:24 NOTICE[16489] channel.c: Don't know what to do with control frame 15 Does Anyone has a clue of how to get rid of that ? May it's because I use the HDLC decoding in hardware ?

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hi, Recommending to go Digium because of an OpenBSD issue with the Sangoma A104D is quite funny to say the least since neither is the TE407P supported in BSD by Digium. So the recommendation is useless to the person who originally requested for a comparison between the two products. If someone wanted to send back the A104D, he could have taken advantage of Sangoma's 30 day money back

Thanks for replying. It's there, /usr/src/zaptel and it's valid. The script checks for its existence before compiling. The only thing that's unusual about this zaptel is that it is patched to support KB2 echo can. Gavin: Thanks, already cc'd Sangoma support. Hope they are working today! -----Original Message----- From: Eric "ManxPower" Wieling

Howdy, Just installed a new switch in a new location (Ubuntu, 2.6.24-24 kernel, zaptel 1.4.12.1 built from source, libpri-1.4.10.1 built from source, asterisk 1.4.26 built from source, wanpipe 3.5.4 built from source, Sangoma A104d with firmware that is probably a year old). I plugged in an RBS T1, ESF, B8ZS, wink start, and MF signalling. I stuck with the defaults that the wanpipe build

Sangoma support did something and the driver is there. Rebooting now with the new card. Hold me, I'm scared. -----Original Message----- From: Colin Anderson [mailto:ColinA@landmarkmasterbuilder.com] Sent: Friday, December 22, 2006 10:09 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [asterisk-users] Sangoma Wanpipe 2.3.4-3 compilation fails un der FC2

Hi ! We curently have a centos 5 / asterisk 1.4 server that we have some DTMF problems with. It has a Sangoma A104d card and only port one is used to connect to the PSTN. Port 2 is conencted via a cross-over cable to a RAS for modem access and port 3 is connected for data communication via PPP. Now, I want to freshen this setup to something newer. So I installed a Scientific Linux 6 server,

LD [M] /root/wanpipe/patches/kdrivers/wanec/wanec.o Building modules, stage 2. MODPOST *** Warning: "register_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! *** Warning: "unregister_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! CC /root/wanpipe/patches/kdrivers/wanec/wanec.mod.o LD [M]

Hey! I am installing Sangoma A102D wanpipe driver and i got following error. what is this ? why dir isn't there ? wanpipe-3.5.16 # make dahdi DAHDI_DIR=/usr/src/dahdi wanpipe-3.5.16 # make install ....Send .... .... Installing Wanpipe Firmware update utility in /etc/wanpipe/util/wan_aftup install -D wan_aftup /usr/sbin/wan_aftup install -d /etc/wanpipe/util/wan_aftup/scripts install:

I'm trying to get my Sangoma B600 working with Asterisk 1.6.1 and DAHDI 2.2. I've tried running ./Setup dahdi (and with --64-bit_4GB flag, running amd64) and the compile fails with this for many versions of the driver (incl. 3.3.16, 3.3.16.22, and 3.4.1): Building modules, stage 2. MODPOST 1 modules CC /usr/src/wanpipe-3.3.16/patches/kdrivers/wanec/wanec.mod.o LD [M]

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC