similar to: Question about OSLEC or HPEC with AsteriskNow

Hi - I had a client recently move their asterisk system (asterisk 1.4.26, dahdi 2.2.0.1, aex800 w/vpm module) to a "new" location, a building that's nearly 150 years old. I was not personally able to go there, but the person who did the move said the building's demarc room was "scary"-- water leaks, jumbled and frayed wiring, and all sorts of other fun. The echo on

Hi all, Just want to check from the list experienced personal about the Digium HPEC, where I had purchased the HPEC and wish to run with TDM card Sangoma A200. I can't install HPEC to run with Sangama A200 card, even I had changed my hpec file from i686 to i386. The error that I had as bellow; > Found key 'HPEC-XXXXXXXXXX' for 2 channels. > Found valid HPEC licenses for 2

Hi List. I've bought a new server for my home asterisk installation and I'm trying to install asterisk with dahdi drivers and OSLEC. To do that I've got the svn dahdi-linux trunk revision 5366 and the echo subproject from the 2.6.28-rc6 Linux kernel sources. As reported in the dadhi README file I've uncommented out the two OSLEC related lines at Kbuild file in the

Does this make a significant improvement? The box in question I was going to try this with has a 4 port TDM card w/ plenty of horsepower, but I do intend to later migrate to a Soekris unit running Astlinux and therefore might not have the power to run it after. If the difference is significant, I may move to an ITX board so I could use a bigger CPU, but only if the hassle is worthwhile. Any

Hi All - I've been trying to compile Zaptel w/ HPEC, but I've been unsuccessful. The system is CentOS 4.4, zaptel version 1.2.15. I believe I've got all the requisite files, and they're in the right locations in the zaptel tree. When I compile, I get the following warning from make: Warning: could not find /usr/src/zaptel-1.2.15/hpec/.hpec_x86_32.o.cmd for

I recently read about the following new technologies from Digium. Has anyone tried the new HPEC or knows when it will be available? TDM800P and HPEC The TDM800P is an 8-port analog telephony interface card, so it fills the gap between Digium's 4-port and 24-port cards. Analog phones and POTS lines are going to be with us for some time, and demand for support for them remains high. The

I am running 64 bit linux on my Asterisk box and would like to get the new HPEC software running on it. However, while there are 32 bit modules available, there are no 64 bit modules on the ftp site: http://ftp.digium.com/pub/telephony/hpec/64-bit/ In some places on the digium website it states 32 bit only and other places including the documentation it states 32 & 64 bit are available.

Hello, Has anyone tried the combination of asterisk 1.2.24, zaptel 1.4.5 and HPEC 9.00.003? In particular, with a hardware configuration similar to: Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Not installed Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) I have two fully independent systems

I wonder if anyone has any ideas on this. I have recently migrated my server from a custom built Linux with Asterisk, Zaptel and Oslec running fine, to Ubuntu Server 8.10. I have Asterisk installed via synaptic at it works fine. I have built and installed the zaptel package by doing the following commands: sudo m-a -t build zaptel cd /usr/src sudo dpkg -i zaptel-modules-{version}.deb sudo

Yesterday I pulled in the latest svn of Dahdi and added the files from a recent kernel in the drivers/staging/echo structure and modified the Kbuild file so it would compile without error. I insmod'ed the module in, and modified my system.conf has echocanceller=oslec. cat /proc/dahdi/1 shows: Span 1: WCTDM/0 "Wildcard TDM410P Board 1" (MASTER) IRQ misses: 1 1

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

Hi, I've a problem: I can't configure DAHDI with ech canceller OSLEC. I have Asterisk 1.4.24 and DAHDI 2.1.0.2. I compiled also OSLEC. But when in /etc/dahdi/systems.conf I insert value echocanceller=oslec,1-4, command dahdi_cfg -vvvvvvvvvvvv give me an error about oslec. Someone can help me? Thanks Marco -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello list, I'm facing a little issue with dahdi attempting to load the OSLEC echo canceller into my current kernel. After compiling dahdi 2.3.0.1 with OSLEC support, I get the following error when set 'oslec' as the echocanceller: DAHDI_ATTACH_ECHOCAN failed on channel 1: Invalid argument (22) - Similar errors are *NOT* present using other echo canncelers. - I tried adding the

Hi All, Which echo cancellation is good between OSLEC and MG2. Dahdi by default use MG2 echo cancellation on channel. If i want to use OSLEC then what should i need to do ? Do i need to recompile dahdi with OSLEC ? -S -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, I install dahdi-linux successfully with the module of oslec for the echo, but when I specify it in the system.conf the echo canceller oslec it shows me errors: DAHDI_ATTACH_ECHOCAN failed on channel 4: Invalid argument (22) I see that the echo cancellers is supported: mg2, kb1, sec2, and sec because oslec is not supported?, but he has support to compile it with dahdi_linux! best

Hi, I'm used to add OSLEC source code into asterisk and use it as default echo canceller. Currently, I'm proceeding this way: download the kernel source code roughly matching the kernel version I'm targeting with command such as "wget http://kernel.org/pub/linux/kernel/v3.0/linux-3.2.46.tar.bz2" copy the echo subtree into dahdi change dahdi's Kbuild file (for dahdi

I have recently moved an asterisk system to a new location. This location is experiencing terrible echo. I installed the HPEC from Digium but that has caused a new problem. When HPEC is enabled and more that 16 taps are used, the audio from the outside caller gets clipped. Instead of hearing: Hello, my name is Mike one hears He o, m ame ike If the taps are set to less than 16, there

In order solve my incoming caller ID problem, I upgrade the dahdi to version 2.6.1 from version 2.4.x. After upgrade, I found the echo cancellation doesn't working (I'm using Digium AEX800B PCI Express card). I can hear my self talking on the phone. How to solve this? I think I need to recompile dahdi 2.6.1 with OSLEC support? how? [root at callcenter ~]# dahdi_cfg -vvv DAHDI Tools

Hi All, I have followed below steps to enable echo cancellation. # cd /usr/src # wget http://kernel.org/pub/linux/kernel/v2.6/linux-2.6.28.tar.bz2 # tar xjf linux-2.6.28.tar.bz2 # tar zxvf dahdi-linux-2.1.0.4.tar.gz # ln -s /usr/src/dahdi-linux-2.1.0.4 /usr/src/dahdi # mkdir /usr/src/dahdi/drivers/staging # cp -fR /usr/src/linux-2.6.28/drivers/staging/echo /usr/src/dahdi/drivers/staging # sed -i

Hi all, After reading great things about the OSLEC Echo Canceller (http://www.rowetel.com/ucasterisk/oslec) and seeing the reactions of people who have tried it on a recent Trixbox thread (http://www.trixbox.org/forums/trixbox-forums/open-discussion/need-people-echo-problems), it sounds like it is the "bees knees" for sorting out echo problems with cards like the x100p. Has anyone