similar to: asterisk systems hang with "hfcmulti_rx no memory for rx_skb"

Displaying 20 results from an estimated 1100 matches similar to: "asterisk systems hang with "hfcmulti_rx no memory for rx_skb""

2009 Jul 20
0
No subject
I'm wondering if hdlc can be the culprit (not sure what it is and what it does). Should I set hdlc to yes in misdn.conf (I'm asking before testing because this is a production system)? misdn.conf: [general] misdn_init=/etc/misdn-init.conf debug=0 ntdebugflags=0 ntdebugfile=/var/log/misdn-nt.log ntkeepcalls=no bridging=no stop_tone_after_first_digit=yes append_digits2exten=yes
2006 Nov 24
1
Installing the b410p card, unable to install mISDN
Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz
2007 Nov 26
0
Digium b410p + mISDN echo
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, We have a BRI installation who is experiencing constant echo with the Digium b410p and mISDN. I have adjusted gains, and originally thought that the desktop phones were at fault, although we experience the same problem when a call is bridged out to an external number. I've tried it with 128 taps (the default and I believe the supported
2011 May 23
3
Latest DAHDI/libpri/Asterisk 1.8 & 1x BRI port HFC based ISDN card?
Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the
2007 Jul 27
1
chan_mISDN module does not load
Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for
2007 Feb 14
1
Asterisk 1.4 and chan_misdn
Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all
2005 Mar 08
0
problem in compiling chan_mISDN
Hi List, I?m having problems compiling chan_misdn: asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes -Wno-missing-declarations -fPIC -I/usr/src/asterisk/include -DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include -I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o chan_misdn.o chan_misdn.c
2008 Oct 20
0
B410P and asterisk 1.6
Hi all, I'm trying to get a digium B410P to work with asterisk 1.6.0.1 (but i have the same problems with asterisk 1.6.0) Official digium documentation cover up to asterisk 1.4.x and suggest to use zaphfc... but as i understood zap is completely gone in 1.6 I tried with misdn (1.1.8, 1.1.7.2 and 1.1.5) and card is recognized correctly by the kernel but chan_misdn does not work as expected.
2008 Jan 23
0
No more audio with 99777 SVN version in certain case
Hi, we have an Debian Etch 4.0 amd64 server with 2 B410P cards. Asterisk SVN r99777 is installed. We tried with mISDN shipped with Asterisk/Zaptel (make b410p) as well as with the latest version from mISDN.org 1.1.7.2. zaptel, ztdummy and crt-ccitt modules are loaded. Output of /dev/zap is: root at SrvPhone:~# ls -al /dev/zap total 0 drwxr-xr-x 2 root root 120 2008-01-23 16:42 .
2010 Apr 11
2
mISDN installation via yum
HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser
2006 Nov 22
1
Zaptel - make b410p fails on Ubuntu 6.10
Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--
2003 Nov 13
2
IAX trunk monitoring
I have an issue where * tries to route a call over IAX to another server even if the server is down. I have included the relevant entries from my iax.conf, extensions.conf, and some debug output. If someone could tell me what I have configured incorrectly, I would appreciate it. Thanks, Stephen -----------iax.conf on voip2---------- [voip1] type=friend username=voip1 host=x.x.x.x (ip
2004 Jul 15
1
zapras - and kernel ??
Hi, I'm trying to get zapras do work, I had downloaded the pppd-source and the 2 patches. I succefull compiled and install the patched version of pppd, but got this error in message-log Jul 15 11:43:32 voip1 pppd[9296]: In file /etc/ppp/filters: unrecognized option 'active-filter' Jul 15 11:43:57 voip1 pppd[9299]: Plugin zaptel.so loaded. Jul 15 11:43:57 voip1 pppd[9299]: Zaptel
2007 Nov 17
1
Building and running mISDN for B410P on Ubuntu 7.04
Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations
2014 Mar 11
1
Linux call router
hello there, I am facing an issue with misd/misdnuser/lcr in the system I am running debian 7 and I managed to install from git misdn/misdnuser but in lcr I am getting: chan_lcr.c: In function 'load_module': chan_lcr.c:3520:24: warning: assignment makes pointer from integer without a cast [enabled by default] make[2]: *** [chan_lcr.po] Error 1 make[2]: Leaving directory
2008 Dec 01
2
[SPAM] - Re: [SPAM] - Re: [SPAM] - Dahdi, b410p and looping from 1 port to another - Email found in subject -Email found in subject - Email found in subject
The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:
2007 Jan 14
1
Problems with mISDN TE line
Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in
2006 Dec 13
0
Help with voicemail
I'm looking to use * for a HQ/branch office topology with fairly few calls over the WAN. The questions I have all pertain to the following architectural pic: http://www.45891.com/misc/arch.jpg I'm looking at a distributed architecture so users are somewhat functional when the link to HQ is down, with a centralized voicemail server to allow for transfer of voicemail messages from user to
2006 Oct 27
1
Iax bug ?
Hello, I'm french, so excuse my poor English. I'm face to a terrible thing, with has stole a lot of my time. On the .184 machine, I've the following iax.conf : [general] rtcachefriends=yes bandwidth=high tos=reliability jitterbuffer=no autokill=yes #include "iax.voip1.conf" #include "iax.renoir.conf" The iax.voip1.conf file contains : [VOIP1] type=friend
2008 Sep 23
2
chan_misdn troubles
Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas