similar to: Questions about Dahdi's /etc/dahdi/genconf_parameters

Hi, My genconf_parameter is : # grep -v "^#" genconf_parameters lc_country fr context_lines remote group_lines 1 bri_sig_style bri echo_can oslec pri_termtype SPAN/* NT (I also tried various identations and syntax for pri_termtype line such as bri_termtype but I still get the same output file). But still, generated system.conf contains

Hello, On a very new system, I've got : # cat /etc/dahdi/genconf_parameters | grep -v "^#" lc_country fr context_lines remote group_lines 1 bri_sig_style bri_ptmp echo_can oslec pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 TE SPAN/4 TE # dahdi_genconf Empty

Hi, I'm using revision 6822 of Dahdi Tools. # dahdi_hardware pci:0000:05:06.0 wcb4xxp+ d161:b410 Digium Wildcard B410P # asterisk -rx "dahdi show version" DAHDI Version: 2.2.0.2 Echo Canceller: OSLEC # cat /etc/dahdi/genconf_parameters ... pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 NT SPAN/4 NT #

Hi, I'm using Asterisk 1.6.1.18 with latest Dahdi Linux and Tools (rev 8854) and libpri 1.4.10.2. During installation, I'm facing this : # dahdi_genconf -v system Default parameters from /etc/dahdi/genconf_parameters Empty configuration -- no spans Of course, I've got span descriptions in /etc/dahdi/genconf_parameters : .... pri_termtype SPAN/1 TE SPAN/2

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

The information (or lack of it) on upgrading from zaptel to that @&*^QW%&^%!!! dahdi is very frustrating. I cannot find anything on how to uninstall zaptel, i found an earlier post to this list which suggested make uninstall and make remove in the zaptel directory which just generates errors and does nothing (on zaptel 12.1). Then i install dahdi-linux and dahdi-tools and i want to

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi, How to properly re-configure dahdi, when for instance I want to change from TE to NT mode ? I'm planning the following operations : /etc/init.d/asterisk stop /etc/init.d/dahdi stop rmmod dahdi rm /etc/asterisk/dahdi-channels.conf rm /etc/dahdi/system.conf rm /etc/dahdi/modules nano /etc/dahdi/genconf_parameters dahdi_genconf -v modules dahdi_genconf -v system dahdi_genconf -v chandahdi

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi, I've just discovered that dahdi_genconf could create configuration files reading a single genconf_parameter file. 1. Is using dahdi_genconf recommended to configure dahdi or is it a helpful tool for specific devices or installation processes ? 2. If not, is there a custom mecanism that would prevent hand-edited files to be written over by dahdi_genconf (you can obviously remove

Hi, these are my first steps with DAHDI and I finally managed to get asterisk to load chan_dahdi (after I found out, that I need libpri). But how do I tell chan_dahdi on which isdn numbers it should react? I haven't found a parameter like "incomingmsn" for chan_capi in the documentation. Thanks for your help, Stefan

Hi I have a TDM400 and 4 channels of HPEC. I don't use the POTs lines much so I didn't realize it wasn't working. This morning I was watching the console and noticed that the echo canceller didn't load when a call came in. /etc/dahdi/system.conf showed mg2 for all 4 channels. I changed them all to hpec and then restarted dahdi and Asterisk and suddenly HPEC was working. Is

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.4.0. DAHDI-Linux 2.4.0, DAHDI-Tools 2.4.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

On Sat, Jan 17, 2015 at 09:31:33AM +0100, Bertrand LUPART - Linkeo.com wrote: > >>> However, dahdi_genconf keeps finding no span: > >>> What am i missing? > >> > >> It looks like your driver is loaded correctly. My guess would be maybe > >> the dahdi-tools is packaged as an older version that doesn't know > >> about the newer te435

Hello, I just installed a Debian Jessie box from scratch which sports a Digium TE435 digital card. I installed the software, built and loaded the kernel modules: # dpkg -l|grep dahdi ii asterisk-dahdi 1:11.13.1~dfsg-2+b1 amd64 DAHDI devices support for the Asterisk PBX ii dahdi 1:2.10.0.1-1 amd64

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hello, I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : $ sudo dpkg -l|grep -Ei 'dahdi|asterisk|libpri' ii asterisk 1:11.13.1~dfsg-2+b1 amd64 Open Source Private Branch Exchange (PBX) ii asterisk-config 1:11.13.1~dfsg-2 all Configuration

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and