similar to: SIP 18x Messages

I am having difficulties with customer-bound DTMF being very short & clipped off (and basically unusable, as systems on the customer side aren't recognizing the DTMF digits, and I can barely tell that DTMF is there when I listen on a handset). My system set up as follows: PSTN <--> Metaswitch <-SIP-> Asterisk <-SIP or IAX2-> CPE Asterisk is running Asterisk 10.4.0 on a

Hi folks, I am having a small problem with asterisk-1.6.2.7 + app_fax on OpenBSD 4.7 -release. Everything seems to work fine. I have a macro which answers, receives the fax to a tiff, and then runs a script (mailfax) to convert that to pdf and email it. It all works perfectly except for some errors I am seeing in the console. After it hangs up I get a dozen or so messages in the cli

I'm (still) trying to get my Asterisk box talking to a Metaswitch. All I'm getting is a "heartbeat" of OPTIONS messages coming from the Metaswitch which my Asterisk box replies to. The exchange looks like: <-- SIP read from 172.b.c.d:5060: OPTIONS sip:metaswitch@206.b.c.d:5060;transport=udp SIP/2.0 Via: SIP/2.0/UDP

I'm attempting to connect to a Metaswitch, inbound only (at this time). The Metaswitch is the only "connection" (at this time). All I'm getting so far is a bunch of "OPTION" messages which my Asterisk box replies to but I don't get inbound calls. Here's my sip.conf. As you can see I've been trying a bunch of different options without success :(

I am setting up VM off Metaswitch due to a problem with Metaswitch VM. I have a couple days to prove this works and I need a little assist please. I am using TRIXBOX 2.6.2.5 and have the Meta SIP trunk up. I have extensions built that can talk to each other. I took a trace on the TRIXBOX that shows when I dial my test phone on Metaswitch it goes to VM after a couple rings and the call goes to my

Hi All, I'm stumped on a weird problem. I have an * server working fine for local SIP phones and IAX2 connections. We just provisioned a second Ethernet port to attach to a local SIP provider. PSTN calls incoming work fine: PSTN -> SIP Provider -> SIP -> * but outgoing calls are not. Call setup takes place and the caller can hear about 1-2 seconds of audio before the SIP provider

Hi, I have a Asterisk that connects to the PSTN via a PRI. After Asterisk sends the setup message it immediately sends a 183 Session Progress. Is there a way I can change it so that it sends a 100 Trying instead? Because I am having some issues with a equipment where it does not play a busy tone as a result of sending a 183 Session Progress then the 486 Busy. Thanks Remi

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

I'm trying to send CallerID info to a MetaSwitch system over a PRI. The MetaSwitch gets the info exactly as it is sent by Asterisk, but I think it might be having trouble with the Hexadecimal b1 that is being sent just before the first character of the CallerID Name. Does anyone know what the significance is of the b1 being sent here? Or, is there a way to make Asterisk not send the b1

I have progressinband=yes in sip.conf, but Asterisk sends a 180-Ringing to my polycom phones and then it also sends 183-Session Progress. That doesn't seem to make sense. Shouldn't Asterisk NOT send 180-Ringing if progressinband=yes ? Doug.

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

Andrew, I don't think it's a Polycom issue. We took Asterisk out of the picture and had our Polycom phones communicate directly with an Audiocodes PSTN gateway. Unlike Asterisk, the audiocodes do not send 180 Ringing before sending 183 Session Progress, and the polycom's play the correct tones in this case. We WANT Asterisk to send progress tones in band. In our case it IS needed.

[Resent due to non-descriptive subject line.] Hi folks When connecting two SIP users, is there any way to stop Asterisk from sending SIP 183 Session Progress messages, either globally or per-peer? Scenario as follows: Call from UA1 to Asterisk (UA2) to UA3. UA3 sends RTP before SIP OK to Asterisk (UA2). Asterisk (UA2) detects early audio from UA3 and sends 183 Session Progress with SDP to

Hello, as a variation of our issues with Adhearsion calls dropping when an INVITE comes in for a bridged call, I now have a new issue to contend with. Our call is in an AsyncAGI application, and has been bridged to another channel. The provider that supplies the DID sends a polling reINVITE every 15 minutes (it's a documented Metaswitch behavior amongst others). The reINVITE is seen as a new

I have a box (Genband) expecting the following: 100 trying 180 ringing with SDP Or 100 trying 183 with SDP And asterisk is sending: 100 trying 180 ringing 183 with SDP Any way to modify asterisk to send what he is expecting? Thanks, Dave -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have this in sip.conf: [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes progressinband=yes [19256002182] type=friend username=19256002182 callerid="Test hone 1" <+19256002182> host=dynamic canreinvite=no secret=password context=test disallow=all allow=g729 [level3] type=peer host=xxx.yyy.16.99 context=default

Hello, I''m trying to port one of our existing appliances (running on 64-bit Red Hat Enterprise Linux 6.4) to a Xen HVM guest . We''re seeing some very odd behaviour that doesn''t manifest on other platforms. The guest experiences intermittent lockups of a few seconds- shell sessions become unresponsive, and various software healthchecking in our application triggers,

Im trying to get my asterisk box to register to a sip provider without much success. here is my console output in asterisk Dec 13 12:57:17 NOTICE[213005]: chan_sip.c:3982 sip_reg_timeout: Registration for 'voicemail.nexband.com@metaswitch.nexband.com' timed out, trying again -- Got SIP response 403 "From: URI not recognized" back from 208.149.73.5 Urgent handler in my

I've been racking my brain for the last two days to try to figure out what I could possibly be doing wrong in my configuration for a SIP trunk that's setup through my local ISPs Metaswitch. I've setup a very simple SIP Peer, which I've played around with a lot in the past two days but still comes back to the following basic setup: [provider-fireball] type=friend

I recently configured a SIP peer which i must specify my fromuser as my ten digit "DID". I send calls to this peer, but whenever Asterisk sends an options message, the fromuser is "asterisk". Is this a bug? Or is there some other config I must make ? register = 2155551941:123456 at 10.0.138.226/2155551941~600 [peer](!) type=peer context=inbound qualify=yes