similar to: DAHDI congestion problem

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've set up an outbound .call system for customer callbacks and the like. Calls are going out over analog lines and I'm trying to use the WaitForSilence routine to make sure the phone has stopped ringing before starting message playback. The problem is that if I set the first argument of WaitForSilence to anything other than 1, WaitForSilence never exits. Some general info on my setup:

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Hello all, Ok it is Sunday afternoon and I am going crazy. I have been running in circles so long that I can't think straight. As an example, I sent this message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2, DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422 at the end of installing dahdi-linux and dahdi-tools I get:

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed