similar to: Problem with Cisco 7911G and ABE 2.1.2C - randomly cannot DIAL

One of our clients is using a Grandstream GXP2000 with an attendant console. We have used the same phone with past clients successfully however this particular operator processes around 200 calls a hours and the GXP2000 for sure does not like the quick line shuffling and call volume. We get the following problems randomly: 1. menu stops working 2. transfer key stops working 3. Line 1 LED gets

If you write a HowTo, would you please insert it into the wiki at http://www.voip-info.org/wiki/index.php?page=LDAP ? Thanks. On Sun, 2008-03-16 at 07:09 -0500, asterisk-users-request at lists.digium.com wrote: > Date: Sat, 15 Mar 2008 18:20:32 -0200 > From: "Gonzalo Servat" <gservat at gmail.com> > Subject: Re: [asterisk-users] LDAP > To: "Asterisk Users Mailing

Dear all, Just wanted to know if any one had deployed the Grandstream GXW 4024 yet. Wanted to hear any feedback and/or problems with this unit that you may have experienced. Thank you. -- Faraz R Khan Chief Architect Emergen Consulting Pvt Ltd www.emergen.biz

Thought i would share this so it doesnt annoy others as much as it did me :) If you recently installed a GXW 40XX and your extensions start ringing magically now (ringing for no reason, pick it up its a clear tone) you need to check the "Disable send MWI" in your gateway. apparently certain old phones do not like the MWI signal and treat it like a ring tone. -- Faraz R Khan

Dear all, Wanted some help on a solution we wish to deploy. There is a central Asterisk server which is connected by some 30+ remote sites. Each site has a substantial number of users within them (200-300). What I wish to do is save on bandwidth by trunking connections between those sites and the main site. I can use a flash based solid state device for this purpose (Xorcom or ASterisk

Hello All, I am trying to setup a small system where Nextone Softswitch will send traffic to Asterisk and then terminate on Grandstream GXW410x IP Analog Gateway but for some odd reasons the call are flashed back from Grandstream to Asterisk and creating a Black loop... I did follow the instructions provided by Grandstream support but it doesn't seems to be working...

Dear All, We have a customer who is opening a new office in Dubai and we know that VoIP is blocked over there. Has anyone a solution to getting VoIP back out (we want interoffice calls back to the UK)? We we're thinking of IAX trunking, but not sure if that is blocked or just SIP etc. A VPN works, but is not great. We have seen: http://www.speed-voip.com/voiceguard.html At the moment it

Anyone use the LDAP feature yet on the polycom phones? If so how well does it work? How are you using it in your environment? http://polycom.com/usa/en/products/voice/desktop/soundpoint_ip/applicati ons/corporate_directory_access.html Roy Anciso Director of Technology Manistee Intermediate School District 772 East Parkdale Avenue Manistee, MI 49660 Ph: 231-723-4264 Fx: 231-398-3036 roy at

Hi All - Anyone know if the "callpark" feature is in ABE? Is there a comprehensive list of the differences between ABE and the open source version? I've only seen a bullet-point chart which has no real detail. Thanks, Noah

Hello list, I am trying to find a solution for interfacing a Dictaphone Freedom recorder. Currently, 4 POTS lines interface to the recorder, and the future will have the 4 lines coming into an ABE server on PRI. The Freedom system is using a standard amphinol connector to a punch down block, where the 4 lines, shared with a Nortel Meridian system, are located. The lines are analog, and per

Hello All, I have a setup of ABE on rPath linux,Sangoma A101D, and a T-1 line (Not PRI) which is all happily coexisting and all lights are green. The T-1 comes in from the world into a "Shark Box" which splits the T into 384K data and 6 channels voice. The data side is working great. The voice side, not so great. It was originally broken out to 6 pots line and Verizon came back

I figured that asterisk can do conferencing if we have zap interface. The BRI cards I have they do not have Zaptel. How do I enable conferencing on my server? Regards Ajey

Greetings list, I've been asked to provide a system for 200 extensions, most of which will be existing analogue POTS handsets, not IP handsets. I've not really had any experience with large channel banks in the past (since most of our deployments are strictly IP-only to the desk), so I'm at a loss as to which ones are worth looking at. If anyone's had experience using channel

I managed to use Cisco IP phones 7911g with asterisk with Sccp and chan_skinny without any configuration files in tftp. Only settings in dhcpd to indicate the tftp address and skinny.conf settings. the problem that I have is that from 8 phones two of them after working a while now are restarting after splash screen . I' ve made a factory reset. Uploaded a SIP firmware but the same.

hi, I'm trying to configure a Cisco IP Phone 7911G in order to work with Asterisk. I have loaded the 8.3.3 SIP Firmware of Cisco through a DHCP and a TFTP server. All seems ok but a file that is downloaded : term06.default.loads (I understand that is for 7906 model) instead of term11.default.loads (I understand that is for 7911 model). In any case the phone reboots well. At this moment I

somebody knows some application web that allows me to call to my internal extensions of my asterisk, example click to call. I was proving the click to call of this example but it doesn't work http://www.voipjots.com/2006/02/click-to-call-with-your-asteriskhome.html greeting rickygm

Anyone know of a SIP phone that supports group listen? Group listen allow you use the handset but what the far end says comes out the speaker...it is F802 on a Norstar. Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080313/a219002e/attachment.htm

Hi, I had asterisk 1.4.17 with the extensions which is configured in the sip.conf it was working fine. Now I am having the requirement to authenticate the SIP users through the OpenLDAP not through the sip.conf. Steps I have done : Did a check out by using the following command, http://svn.digium.com/svn/asterisk/trunk. [^] then given configure, make , make install. and taken the sample ldap

Hello Has someone written a web page (preferably PHP) that simply shows what extensions are currently online? Thank you.

Hello, How can I make a live chat (mainly text, but with voice/video chat if possible) interacting with asterisk? Can asterisk control simultaneously the queue between people calling by phone and people by web chat? At my work, there is a call center using asterisk to control the queue of the clients (by phone) already. This part is ok. But now I need to make a chat room at the website