similar to: mISDN NT mode config setting

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello. Just installed the Beronet BN4S0 card. But i can't connect to my ISDN Line. misdnportinfo gives (what does ":Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib" mean?): best regards and thanks t. asterix asterisk # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Sorry for bad english I installed asterisk and misdn by svn co http://svn.digium.com/svn/asterisk/team/crichter/0.3.0 asterisk-0.3.0 but asterisk don't show any channel and /etc/init.d/misdn-init restart ------------------------------------------- Unloading module(s) for your misdn-cards: ------------------------------------------- rmmod hfcpci /etc/init.d/misdn-init: line 282: 20170

Hello all! I just noticed, that since installing the latest SVN branch (152803), I receive the following error, when loading/reloading the misdn.conf file misdn reload [...] [Nov 3 16:20:37] WARNING[5267]: misdn_config.c:938 _build_general_config: misdn.conf: "misdn_init=/etc/misdn-init.conf" (section: general) invalid or out of range. Please edit your misdn.conf and then do a

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hello I fixed my problem. I changed user and group in /etc/mISDN.conf: <devnode user="asterisk" group="asterisk" mode="644">mISDN</devnode> now it works again! Thanx 4 help! ;) Ingrid -- "Bonnie & Clyde der Postmaster-Szene!" approved by Postfix-God http://wetterstation-pliening.info http://dokuwiki.nausch.org --------------

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Hello, I have a strange problem with misdn.conf When I run asterisk, I have this message : Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config: misdn.conf: "use_callingpres=yes" (section: general) invalid or out of range. Please edit your misdn.conf and then do a "misdn reload". Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config:

Hi, I have a Fedora 7 xen system with a domU to which I have delegated via pciback two isdn pci cards. One is a HFC-S card, the other a AVM Fritz!Card Pci 2.0. In the domU I load mISDN drivers for the cards. The two cards are recognized and function well UNTIL I either decide to unload one or both of the card driver modules (hfcpci and avmfritz) or I decide to shut down the domU. At this

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.