similar to: MeetMe and dedicated conference room phone

I've just noticed a strange behaviour with a MeetMe conference. I have a pair of phones (GS BT102) on my desk, and dialled both of them into a conference on speakerphone. If I spoke or made a sound, I heard it replayed from both speakers together a split second later, as expected. I went away for about 15 minutes, leaving the conference running. When I came back any sound I made came back

My system is linked to a legacy PBX via Q-SIG and most of my tests so far have been from that PBX. I created a number of MeetMe conference rooms and they work fine when called from the legacy PBX. However, when there's a MeetMe room with a legacy caller and a SIP phone, the SIP phone can hear the legacy caller. But the legacy caller can't hear the SIP phone. However, "meetme show

Hi all, Anyone know how to dynamically create meetme conference rooms on the flight? I remembered a while ago there was a switch that tell meetme to create the conference room is the room is not defined in the meetme.conf. It doen't seem to be working for me anymore. Thnx

Software zur Erkennung von "Spam" auf dem Rechner priamus.teamware-gmbh.de hat die eingegangene E-mail als m?gliche "Spam"-Nachricht identifiziert. Die urspr?ngliche Nachricht wurde an diesen Bericht angeh?ngt, so dass Sie sie anschauen k?nnen (falls es doch eine legitime E-Mail ist) oder ?hnliche unerw?nschte Nachrichten in Zukunft markieren k?nnen. Bei Fragen zu diesem

We have two Linksys 942 phones which sound great when they call each other directly through Asterisk. But when they both dial in to a meetme conference room, the sound is very jittery. Other phones like Polycom 501 and Snom 360 sound fine when using meetme. Both Linksys phones are set to use the default g711u (ulaw) codecs. Adjusting the jitter buffer and jitter level settings to various values

Hi, Is it possible to create a meet me room on the go through dial plan? I am looking to use AMI Originate to drop a call into meetme room and once it's proved that party is joined, play him an announcement, grab few numbers from them, and then dial a second number and drop into the same meetme room. The reason to use this is to be able to know when the channels connected because both

?? Hello.? We are very successfully using asterisk (in the form of trixbox 2.2/asterisk 1.2).? We run a few conference lines for customer teleconferences which mostly work well but they seem to operate at half duplex.? If a person starts talking they will cut off others on the call.? Is this normal behavior?? Are there any options I can change to change this? ?? Thanks! James -------------- next

I'd like to monitor key press in a meetme room. Is it possible when connecting one side of a local channel in the meetme room and the other side of the local channel to an agi with the command "wait for digit" ? Thanks Eric

I have meetme working with BLF on polycom phones however when meetme is not actually being used by anyone the 'status' of meetme becomes "idle". Which the Polycom phone sees and produces a clock symbol and FLASHING red LED. Are there any 'tricks' or work-arounds to change this status to something that does not blink the phone's LED making it look busy when meetme is

Has anyone a solution for me - with "Meetme(,Ms)" asterisk plays "conf-invalid" if a room not exist - with "Meetme(123,Ms)" asterisk plays not "conf-invalid" if the room not exist and asterisk hangup I am happy about any proposal. Thanks Daniel

I have encountered a frustrating problem with the meetme rooms and calls entering the system on the Digium analog cards. The typical scenario is: Callers on SIP phones, X-lite, Eyebeam, Cisco 7960, IAXy Callers entering the system from the PSTN via the digium Analog card (TDM400P) In the meetme room the SIP connections can all hear each other loud and clear. The PSTN people can hear

Hi, I know this question may have been asked before (although the archives don't seem to suggest it), but has anyone had any problems with Asterisk accepting a PIN number for a conference room. At this point in time I have established the conference definition in the meetme.conf file as well as specifying the appropriate lines in the extensions.conf file. meetme.conf file: conf =>

I'm trying to record a Meetme conference to disk, but the Monitor application doesn't seem to play nicely with Meetme. In extensions.conf, I have this: exten => 1000,1,Answer exten => 1000,2,Monitor exten => 1000,3,Meetme This starts up the monitoring OK, and it records the prompts that Meetme gives, but as soon as the user enters the conference, the -out WAV file stops

I'm trying to use the password entered with Authenticate to create dynamic meetme conferences with the following dial plan: exten => _XXXXXXXXXX18467,1,Authenticate(/etc/asterisk/meetme.pw|a) exten => _XXXXXXXXXX18467,n,MeetMe(CDR(accountcode)) ; 281-8467 However CDR(accountcode) is always being set to 1022 no matter what password is used. The passwords are stored in a file so they can

Hi, im using asterisk-1.2.24 and zaptel-1.2.20, im having a problem running meetme conference, when i try to call meetme i get this from the asterisk console Aug 24 00:14:12 WARNING[15466]: pbx.c:1720 pbx_extension_helper: No application 'MeetMe' for extension (sample, 65000, 1) i recompiled my zaptel and asterisk, but the app_meetme file still didn't install, what am i missing

Hi All, I recently had an incident where a conf bridge was left open due to improper disconnection. I've read about the meetme options and marked callers closing the bridge when they exit. This is OK for meetme, but I'm really interested in a call timer that can be set on inbound and outbound calls within the dial plan, per call. I have another customer who wants to offer free calls,

Hi, I was just wondering how would the application be where the Asterisk calls a number and that number joins the conference as soon as the call connects. There would be only one conference already defined in meetme.conf and there is one person already joined the conference. Currently MeetMe requires a person dialing into it and the joining the conference. How could this be done using MeetMe or

Hi all I want to use conference in Asterisk. I configure a conference room in meetme.conf (as conf => 600,1234) and extensions.conf as (exten => 600,1,MeetMe(600,i,1234)) . When i call the extension 600, i have the following message in the asterisk logs: WARNING[7758]: pbx.c:1688 pbx_extension_helper: No application 'MeetMe' for extension (conference, 600, 1) == Spawn extension

I haven't seen this appear on the list, so I thought I would resend it... Sorry for the repost if it did appear before... ----- Forwarded message from Michael George <george> ----- Date: Wed, 3 May 2006 21:48:09 -0400 From: Michael George <george> Subject: meetme conference latency degrades... To: asterisk-users@lists.digium.com We have recently started making more frequent use

I have a peculiar situation, and am hoping someone on the list can offer assistance. I am running CVS HEAD, and am using ITSPs for DIDs. The server has no Zap hardware, but is configured to use ztdummy. All incoming calls are via IAX2. Calls ring to SIP phones, voice mail, IVR, etc., with no trouble. I am also able to transfer calls among my SIP devices, voice mail, IVR, etc. All of my SIP