similar to: 2 single span TDM cards in asterisk

Displaying 20 results from an estimated 60000 matches similar to: "2 single span TDM cards in asterisk"

2012 Dec 21
2
dahdi timing source multiple cards
I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72
2011 Sep 13
1
High delay from Asterisk as PSTN simulator
I'm trying to use Asterisk as a PSTN simulator to run performance tests for echo cancellation algorithms. I'm using the following configuration: SIP <-----> Asterisk 1 <----> Asterisk 2 <----> Echo() Asterisk 1 and Asterisk 2 are connected using E1. Echo() is the dialplan application. The problem is the high delay using this configuration: 20 ms only in Asterisk 2.
2009 Jan 26
3
Digium TE220 card partially detected
Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware
2007 Dec 02
1
T1 Timing Troubleshooting
I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM
2011 Mar 30
5
chan_dahdi unknown dependency problem
So, I've compiled and installed libpri-1.4.11.5, dahdi-linux-complete-2.4.1+2.4.1 and asterisk-1.6.2.17.1, but chan_dahdi is not getting built. If I do a "make menuselect" in asterisk I see it listed with XXX, meaning that dependencies are not met. XXX chan_dahdi Depends on: res_smdi(M), dahdi(E), tonezone(E), pri(E), ss7(E), openr2(E) res_smdi gets built fine, dahdi is
2006 Mar 30
3
Span monitoring
Hi, Does Asterisk have builtin (T1 or E1) span monitoring? If a span goes down, will asterisk know about it. Personally, I would like to have a event generated through the Manager API interface. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060330/cde18abb/attachment.htm
2012 Mar 02
2
Digium FXS specifications and limits Question
Howdy All, I'm considering Asterisk / Digium as a replacement to my existing phone switch. I need to continue to be able to push analog lines between multiple buildings in a campus environment. The Digium Analog 410 Card manual states it's not recommended to go beyond 1500 feet distance for an FXS card, and no line should leave the building or be bundled. The 2400 Series Manual does
2012 Jun 11
1
Which Digium cards to select: AEX with EF or E or P or B?
Dears; I need to order Digium card and not able to know which one is the best quality? Is it that of AEX with the end E or EF or P or B? I saw those card that its slot is small (I think those that end by EF), are they the best card? Really I am caring to have a card that has echo cancelation and the voice volume is high enough (because previously I faced the problem that the voice volume was
2009 Dec 23
4
Dell Server suggestion
Hi, I am in need of ordering a new server here for our asterisk solution. Since the corporate standard is Dell we need to stick to a dell server. We used to deploy 2900III without any issues, however now they are almost not available any more and are looking at a new solution. Has anyone tried any of the new Dell R (series) servers with Asterisk, utilizing Digium PRI cards? The biggest issue I
2011 Feb 13
1
Fax for Asterisk SIP-TDM
Is it possible to do SIP<->Asterisk<->TDM in a single step with FFA? Or does FFA always use TIFF files? I'm using Free FFA on 1.6.2.15 and I want to be able to use SPA 2102 ATA's at the fax machines and send faxes directly over a PRI. Mark -- Mark Willis Star One Telecom Office: 1-800-889-7001 Cell: 210 880 5097 http://staronetel.com
2010 Apr 22
3
How to do analog e&m on asterisk?
Hi, Can anybody with previous experience with it guide me on how to setup asterisk with analog e&m to connect it to an old style e&m system which uses 4 pair cables on RJ 45 jacks. All the analog cards I know of use RJ 11 jacks. And there is no choice of modernization of the customer equipment. Cable pin out are as follows: 1. M lead 2. E lead 3. Tip1 4. Ring 5. Tip 6. Ring1 7. SG 8.
2009 Aug 18
2
DAHDI - better to have card?
Hello, I have at my disposal, 2, TE410P cards. I have setup an asterisk box that will function ONLY to handle meetme conferences over SIP. No PRI lines to be plugged into the 410 card. MeetMe requires an external timing source. Right now, using the dummy driver. Is it possible to use the card solely for timing purposes? Any benefit to doing so? Or should I just sell the cards? Matthew
2005 Aug 23
8
HDLC/Zaptel/Kernel 2.6.11(.9)
All, I'm having a heck of a time getting hdlc to work on kernel 2.6.11.9 .. I compiled hdlc, hdlc_gen, hdlc_cisco, hdlc_raw, into the kernel (note into, and not 'modules'). System comes up, I configured zaptel.conf span=1,0,0,esf,b8zs nethdlc=1-24 modprobe wct4xxp ztcfg sethdlc hdlc0 cisco ifconfig hdlc0 up All of this works fine, believe it or not. I have a T1 cross plugged
2011 Aug 03
1
TE410P hardware problems
TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and
2010 Oct 22
1
E1 and T1 on the same card, or on the same server
Hello list, (Resending this email due to a typo in previous copy) I need to do E1 to T1 conversion for a project, and was wondering if there exists a card with both E1 and T1 on it. Or is it possible to use two separate cards in an asterisk box, one for E1 and one for T1? (Please don't mention aculab or adtran, dealt with them in the past, won't deal again.) I talked to Digium and the
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to
2005 Jan 24
2
Wildcard TE405P and TDM400 - TDM not working
Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,
2009 Sep 30
6
question on pri intense debug
Running asterisk 1.4.26.2 help pri pri debug span Enables PRI debugging on a span pri intense debug span Enables REALLY INTENSE PRI debugging pri no debug span Disables PRI debugging on a span pri set debug file Sends PRI debug output to the specified file pri show debug Displays current PRI debug settings pri show spans Displays PRI
2003 May 31
5
CAC ADIT600 / T400 config
I know a few ppl have those CAC Adit 600's with t400 I can't seem to get my second span up on the T400 connected to the second spand on the adit (A:2) A:1 seems ok Can someone post they zaptel.conf span defintions And maybe a "print config" from the adit 600 cli I think my issue is timing srcs the coding, framing. bld out are all matched thx -------------- next part
2012 Jan 04
3
Anyone have a reliable T.38 Solution
Aloha, We are looking to roll a solution that will have the following network layout: ISDN-PRI <--> Asterisk <--> T.38 <--> ATA <--> Fax Does version 1.8 with the Digium fax driver have this capability? I like 1.8 because it is a long term support version. What ATA's are people using? Any working solutions would be great! Aloha, Matt