similar to: HPEC > VPM ?

I was previously using an old computer running Asterisk 1.2 with zaptel. Once the CPU fried I switch to a new computer and I chose AsteriskNow 1.5 running in 64bits to simplify the installation process. I manage to find my way with configuring dahdi instead of zaptel and to switch all my previous config to the new computer. Now everything is fine except that even if I use the md2 echo

Hi all, Just want to check from the list experienced personal about the Digium HPEC, where I had purchased the HPEC and wish to run with TDM card Sangoma A200. I can't install HPEC to run with Sangama A200 card, even I had changed my hpec file from i686 to i386. The error that I had as bellow; > Found key 'HPEC-XXXXXXXXXX' for 2 channels. > Found valid HPEC licenses for 2

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

Does anyone know how to disable the VPM in software rather than removing the card altogether? The canceler isn't working as well as the software cancelers were. Aaron

Hi All - I've been trying to compile Zaptel w/ HPEC, but I've been unsuccessful. The system is CentOS 4.4, zaptel version 1.2.15. I believe I've got all the requisite files, and they're in the right locations in the zaptel tree. When I compile, I get the following warning from make: Warning: could not find /usr/src/zaptel-1.2.15/hpec/.hpec_x86_32.o.cmd for

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

I recently read about the following new technologies from Digium. Has anyone tried the new HPEC or knows when it will be available? TDM800P and HPEC The TDM800P is an 8-port analog telephony interface card, so it fills the gap between Digium's 4-port and 24-port cards. Analog phones and POTS lines are going to be with us for some time, and demand for support for them remains high. The

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

I am running 64 bit linux on my Asterisk box and would like to get the new HPEC software running on it. However, while there are 32 bit modules available, there are no 64 bit modules on the ftp site: http://ftp.digium.com/pub/telephony/hpec/64-bit/ In some places on the digium website it states 32 bit only and other places including the documentation it states 32 & 64 bit are available.

Hello, Has anyone tried the combination of asterisk 1.2.24, zaptel 1.4.5 and HPEC 9.00.003? In particular, with a hardware configuration similar to: Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Not installed Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) I have two fully independent systems

Does this make a significant improvement? The box in question I was going to try this with has a 4 port TDM card w/ plenty of horsepower, but I do intend to later migrate to a Soekris unit running Astlinux and therefore might not have the power to run it after. If the difference is significant, I may move to an ITX board so I could use a bigger CPU, but only if the hassle is worthwhile. Any

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

I have recently moved an asterisk system to a new location. This location is experiencing terrible echo. I installed the HPEC from Digium but that has caused a new problem. When HPEC is enabled and more that 16 taps are used, the audio from the outside caller gets clipped. Instead of hearing: Hello, my name is Mike one hears He o, m ame ike If the taps are set to less than 16, there

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

I just purchased an Amfeltec USB-FXO adapter and am trying to compile DAHDI 2.10 on a Raspberry PI running Pidora 2014 R3. I have all the dependencies but I get an error and cannot finish. Is it even possible to compile DAHDI for the ARM plataform? Here is the error I am getting: root at astpi dahdi-linux-complete-2.10.2+2.10.2]# make make -C linux all make[1]: Entering directory

Hi List. I've bought a new server for my home asterisk installation and I'm trying to install asterisk with dahdi drivers and OSLEC. To do that I've got the svn dahdi-linux trunk revision 5366 and the echo subproject from the 2.6.28-rc6 Linux kernel sources. As reported in the dadhi README file I've uncommented out the two OSLEC related lines at Kbuild file in the

Any idea why I can't build HPEC for zaptel 1.2.18? It builds fine with 1.4.3... PaulH

Hello, Are HPEC (ie zaptel 1.2.X) and bristuff compatible ? And the results ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070413/b5adde2a/attachment.htm

Hi, everyone: I am developing a system using Asterisk, TDM-400 analog cards, analog lines, and Polycom SIP phones for internal extensions. Initially there was bad echo but after a series of efforts, I've managed to reduce it to a negligible level (it only happens when both parties speak simultaneously, and even there, only for a few hundred milliseconds). From an echo standpoint, things are

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0-rc1 DAHDI-Tools-v2.7.0-rc1 dahdi-linux-complete-2.7.0-rc1+2.7.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: *