similar to: Dell poweredge T100 & TE420

Just purchased a couple of T100 and E100 cards in order to interface from our company's proprietary system through a linux gateway. I am new to Asterisk and Digium. After installing the T100 card, I went looking for drivers for this card. Are the drivers built into the Asterisk application? If so, how do I enable the card through Asterisk? Are there any good getting started documents for a

I have just built a new system using an HP DL360G7 with a TE420 T1 card, and this is the first system using a generation 7 server. I'm not sure whether that is an issue or not. I am using Asterisk 1.2, and Zaptel 1.4.12.1 with patches for GEN5 of the TE420 card. I have successfully used this combination on several systems based on the DL360G6 and TE420(gen5), which have been in production for

Hello, I'm having problem connecting my Asterisk 1.4.29.1 with Digium TE420 to providers Cisco 2800 with VWIC-1MFT-E1 card. the same card runs fine with another E1 provider. TE420 led's lite green. Message type: RELEASE COMPLETE (90) < [08 02 80 ac] < Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: User (0) < Ext: 1 Cause:

<rant level="mild"> I tried emailing support and got a rejection notice saying to go via the website, which then wants registered product details before it will let me enter a support request. Unfortunately, the card was bought by my customer, not by me :-( So I'll just have to ask here... </rant> I am currently trying to replicate an existing system build using new

I just added 2 Digium T100 cards. When my * box boots, it found them and configured them. When I enter genzaptelconf, it comes back with the following error: line 13: Unable to open master device '/dev/zap/ctl' Unloading zaptel hardware drivers: Removing zaptel module: rmmod: module zaptel is not loaded [FAILED] Loading zaptel

Hello all- So I have * up and running and connected to a legacy system via em_w lines and have no trouble dialing from * through the tie line but from the PBX across the tie line I am having intermittant receipt of the DTMF. T-Berd testing is showing that the digits are coming across but * is either missing the first digit consistantly. This seems to me to have something to do with start timers

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15

Hello! Just got new server with TE420. Not all four spans will be used immediately, but spans not configured or not connected blink red light. Is it possible to turn span off, so my colleagues will not eventally tell me that something is wrong with asterisk? :-) Thank you!

Hi I'm having problems getting the TE420 working in HP DL380G5 servers. The cards don't seem to be detected 100% by the BIOS. With two cards in the server they are never detected. things I've tried: 1 Update firmware to latest (P56) for the server 2 change irq settings 3 disable all onboard devices on server and remove raid controller 4 different cards in different slots What I

Hello, I am not entirely sure the subject line captures what I am trying to do, but hopefully this description of the problem will help folks to see my challenge and hopefully offer constructive assistance. I have an experimental setup where I measure the decrease in oxygen in small vials as an organism, such as an oyster, consumes the oxygen. Each vial is calibrated before the experiment and

First time doing a t-1 config with *. running FC2 and CVS as of last W/E. i run modprobe wct1xxp and I get "Unable to open master device '/dev/zap/ctl' i look at /dev and there isn't even a zap directory. i was looking around and found something in /udev that looks promising but not sure what the deal is. ztcfg returns 24 channels configured but the same notice at the bottom

Hi, Does anybody have any feedback on this new card from Digium? It was announced a couple of weeks ago but now Digium said they ran out and is no longer available for purchase via their web site. I find this kind off odd. If they are out why don't they just says its on backorder or something, rather than pulling it off completely from the store. I am kind of hesistant at this point

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hello everyone. I have a timing slips errors and I can't understand what source of the problem is. My installation has 2 digium cards: TE420 and TE220 cards in one server. There are 3 spans (E1) to PSTN and 3 spans to internal PBS stations - normal installation for transit communication. Span configuration is: span=1,1,0,ccs,hdb3 #TE420 - first port. To PSTN. span=2,0,0,ccs,hdb3 #TE420 -

Asterisk 1.4.32 dahdi-2.3.0.1 Centos 5.5 Digium TE420 CAC channel bank (2) Cisco RVS4000 router Cox 50 Mbps/ 5 Mbps cable modem Flowroute provider codac G-711 90 % CPU idle callwaiting=no When there are 10-15 or more calls up the farend hears a callwaiting like beep every 3 to 6 sec. the duration of this "beep" is very short and would be no problem if it didn?t happen every few

Hi, I have a data file which is named test.txt as below. Prior to that, I have converted the last row from nominal to numeric using as.integer. Statement T1001 T1002 T1003 T1004 T1005 T100 T1014 T1021 T1022 T1023 1 0 0 0 0 0 0 0 0 1 0 0 2 0 0 0 0 0 0 0 0 1 0 0 3 0 1 0 0 1 0

Hi All I'm having some serious kernel panic while using digium cards. It may be related to IRQ shared. Can this cause a lot of drop call and bad voice quality ? Do you guys know if there is a way I can assign one IRQ for each digium card ? Thanks a lot. Here is the output of /var/log/syslog kernel: [ 3821.982893] Uhhuh. NMI received for unknown reason 20. kernel: [

So historically I've done one of two things on systems where I've needed to use MeetMe * used a real Digium card, and I've only ever used a TE400 or a TE420 for that purpose, and I know they have the timing chip * used dahdi_dummy, which works well with light load, but I had it running on a very overloaded server and had audio quality issues. I may have had quality issues even with a

https://bugzilla.mindrot.org/show_bug.cgi?id=2462 Bug ID: 2462 Summary: Option to try connectiing to multiple DNS names Product: Portable OpenSSH Version: 6.9p1 Hardware: Other OS: Linux Status: NEW Severity: enhancement Priority: P5 Component: ssh Assignee: unassigned-bugs at

Hello all, I have premisys 24 port fxs channel bank that is connected to a Wildcard T100 card. I also have a pri coming in from verizon that is going to another T100 card in my box. I've downloaded the latest CVS, I went into the file /etc/zaptel.conf and added the following lines: span=1,1,0,esf,b8zs span=2,0,0,esf,b8zs bchan=1-23 dchan=24 fxoks=25-48