similar to: How to notify that a message is waiting using RingTones with a Dahdi-connected analog phone ?

Hi All, I am running into a problem setting the ringtones via _ALERT_INFO on the Cisco 7960 phone. I am using * 1.2.1 and have tried setting the variable to several values. I have also tried setting the phone's software to both 7.5 and 8.2 thinking that it might be a version issue, but with no success. I have examined the packets and do see the ALERT_INFO header being sent, but the

I own a TDM2400 board, with three FXO modules and one FXS. I'am having trouble with analog sip phones, from two different equipment. (Grandstream GXW-4024 192.168.0.105, and Audiocodes MP202), sometimes when I am calling someone, then I press flash, and then call someone else, both calls stay connected after I hang up. [Sep 29 07:18:06] VERBOSE[3218] logger.c: -- Called g2/16 [Sep 29

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

hello all...I have been trying to get a handle on CallerPres with an analog handset. I have usecallingpres=yes in my chan_dahdi.conf file and when I dial *67 on my analog handset I see Disabling Caller*ID on DAHDI/4-1 but when the call is then forwarded to my outbound SIP provider the RPID header is not correct privacy=off;screen=no instead of full and yes how can I correct this?

I have the following entry in zapata.conf, but I don't get stutter dialtone when there is a message waiting. Suggestions? Please? callgroup=1 pickupgroup=1 callerid="Paul mahler" <100> context=inside mailbox=100 channel => 1 Thanks, Paul

Hi, I would like to tune rx/tx gains using dahdi-monitor for a system which will be connected to french PSTN. I'm not aware of any public phone number in France I could call to get a "normalized 1004Hz signal". My questions are : 1. Does such numbers exist ? Is there a directory somewhere listing some of them ? Do you think regulations could make providing such numbers mandatory

I have just successfully got the TFTP file remapping to work such that I can have unique ringtone files for each and every extension. I added the following to my server_args line in the xinetd configuration for TFTP: -m /home/asterisk/grandstream/ringmap.cfg Now the entire line reads: server_args = -v -s /home/asterisk/grandstream -u asterisk -m /home/asterisk/grandstream/ringmap.cfg (There

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

Hi, Long story short - I have an ancient Britsh Telecom phone attached to my Asterisk PBX via Dahdi. It works beautifully, receiving calls, and the call quality is excellent. However, dialling out is impossible, as Asterisk consistently mis-reads the number of pulses the dial sends (it could be a squiffy dial, I'm not sure). Not to mention the fact that, in today's modern "want

-- Attempting call on DAHDI/1wwwwww for smvoice_callprogress at smvoice-dialout:1 (Retry 1) [Oct 16 14:36:42] WARNING[16408]: chan_dahdi.c:8132 dahdi_request: Unknown option 'w' in '1wwwwww' [Oct 16 14:36:43] WARNING[16408]: chan_dahdi.c:1481 dahdi_enable_ec: Unable to enable echo cancellation on channel 1 (No such device) Does DAHDI not know about the W ??? I think zaptel used

Using Asterisk 1.6.1.14 and dahdi 2.2.0.2+2.2.0. We're placing outbound calls over an analog line. Some of these calls are going to cell phones that play music rather than providing a standard ring. As a result, the Dial command sometimes returns a DIALSTATUS of CHANUNAVAIL and sometimes it returns BUSY. The problem is that this is happening on calls that are being answered. Has anyone else

Hi all, I've been modifying the ringtone on a group of Snom phones like this, depending on certain dial-plan conditions: Exten => s,1,SIPAddHeader("Alert-Info: <http://192.168.0.200/tel_ring01.wav>") exten => s,n,Dial(SIP/mjc_office&SIP/mjc_home&SIP/mjc_lab&SIP/mjc_server,20,trj) Now, I'm migrating slowly to Digium D70 phones, which have a different

Hi, When I use the analog phone connected to Zap/1 how do I transfer & hold the caller ? When I hit the flash key, all that happens is the caller hears a beep (sounds like DTMF). But no stutter dial tone on the Zap/1 Port, just continuing conversation with the caller. What could be wrong here? Cheers Jay

2009/3/17 Olivier <oza-4h07 at myamail.com> > > > 2009/3/16 Olivier <oza-4h07 at myamail.com> > > Hi, >> >> I'm rather new to this domain so I may be doing stupid things without >> being concious of that. >> >> I've got a Patton MATA I'm trying to setup as T.38 fax adapter. >> Whenever I connect a fax machine (Dell

Hi, I feel I've read a thread about this previously but I couldn't find it. Is there way for an Asterisk server to check if a sip phone is forwarded without bothering phone's user ? I was thinking of some Alert-Info option that would let the phone reply with a 302 Moved Temporarily or 182 Queued message and not let the phone ring or display anything on its screen. So that, you could

Hi. I noticed that if new messages are recorded with voicemail2 , they're not detected by the message waiting indicator, so the mailbox=XXXX param has no effect, and no message waiting is sent to the phone (sip & adsi, or stutter dialtone) Any hint? -- Brancaleoni Matteo <mbrancaleoni@espia.it> Espia - Emmgi Srl

Hi, I'm using a two-years old installation script for the first time on a Squeeze (linux 2.6.32) platform. For an unknown reason (might be an obvious one), Dahdi can't be loaded anymore. 1. First of all, it seems /dev/dahdi content was previously (ie in Lenny) owned by asterisk:asterisk (asterisk is run as asterisk). Now it is owned by root. Any clue about this ? 2. Secondly, I changed

In the docs for the zapata.conf file I see a setting called call waiting, presumably for giving the call-waiting beep to an analog phone rather than just returning immediately from Dial() with a return value of 0 and the priority increased by 101. In short, I would like to: Rather than catch a busy line after an immediate return from Dial() I would like Dial() to give a call-waiting beep and

Some recent issues I had with hardware seem to come back to not understanding two very similarly named files: /etc/asterisk/dahdi-channels.conf /etc/asterisk/chan_dahdi.conf I've modified the chan_dahdi.conf to work now, but it would appear all I needed to do was include dahdi-channels.conf in chan_dahdi.conf and the problem would not have persisted? Is it me or is that a bit Monty Python?

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not