similar to: Digits timeout (ISDN)

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hi, I have an Asterisk 1.2.9.1 with chan_misdn 0.3.1-rc23 and a beronet octoBRI on a Debian box I have to set up instead of an old legacy PBX. My problem is I get only the base DNID and not the extensions (the last two digits) in Asterisk but the old PBX got all the DNID number so I think it is the card. Is there anybody experiencing a problem like this? How can I solve it? Any ideas? TIA

hi, i've a wirded problem, i try to dial out, using this dialplan [default] exten => _*7.,1,Macro(anrufextern-sip,${EXTEN:2}) [macro-anrufextern-sip] exten => s,1,SetCallerID(SIP-ID) exten => s,n,Dial(SIP/${ARG1}sip-out) exten => s,n,Hangup() when i use my analog telephone, everything is okay: - Starting simple switch on 'Zap/3-1' -- Executing

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi, I have switched a while back from chan_capi to chan_misdn. When the number is dialed and the phone is then picked up everything works just fine. Some users however FIRST pick up the phone and then start to dial... I did not get this to work with misdn. When two digits have been dialed, asterisk sees the extension as complete and does not wait for further digits. I am using an midsn NT

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hello, I have a strange problem with misdn.conf When I run asterisk, I have this message : Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config: misdn.conf: "use_callingpres=yes" (section: general) invalid or out of range. Please edit your misdn.conf and then do a "misdn reload". Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config:

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Hello, Following my first mail about this issue [1], I think I know now what the problem is. When I have both lines being used and a third call comes in, the person calling doesn't get a busy tone, he gets something like line unavailable. I've been debugging mISDN and I think the reason is because asterisk is sending the release cause as 0. P[ 3] --> channel:0 mode:TE cause:0

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi helpers, I seem to have a problem of intermittent DTMF tones being played during a conversation. Eg: Extn 100 takes an inbound call and all is fine. Except, at an undetermined time the person on extn 100 will here a DTMF tone for no apparent reason (it's not the caller pressing buttons). The caller doesn't hear the tone - only the called person. The call itself progresses normally.

I'm wondering if hdlc can be the culprit (not sure what it is and what it does). Should I set hdlc to yes in misdn.conf (I'm asking before testing because this is a production system)? misdn.conf: [general] misdn_init=/etc/misdn-init.conf debug=0 ntdebugflags=0 ntdebugfile=/var/log/misdn-nt.log ntkeepcalls=no bridging=no stop_tone_after_first_digit=yes append_digits2exten=yes

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

Checkout Beronet ISDN cards and Berofix Gateway (appliance or pci card) Personally for my last installation I chose Berofix card which is rock solid and reliable, yet easily configurable. With berofix you don't need telephony drivers on the host system, the isdn card is detected as a NIC and all configuration is done using a web interface. Then you configure FreePBX a new trunk to use the

I'm having trouble installing Beronet BN4S0 card. I have downloaded instructions from here http://www.beronet.com/download/card_installation_guide.pdf And when I download install-misdn-mqueue[1].tar.gz I untar it and execute "make" and "make install". This is the output that I get. [root@nbirma1 install-misdn-mqueue]# make install make -C app_bundle make[1]: Entering