similar to: Cause 34 still there

I have installed two HFC PCI A-cards running zaphfc from bristuff-0.0.2, which seems to work quite fine, but I continously receive the messages "D-Channel on span 1 up" followed by "D-Channel on span 1 down" with a few seconds interval. Why is that? Bri intense debug log and configuration files below. I don't need ztdummy or zaprtc, do I? I get some frame slips as well,

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Any ideas? Sangoma support is closed for the evening. I have the latest Sangoma drivers and Asterisk 1.4 everything installed. When I fire up asterisk, I keep getting "Primary D-Channel on span 1 up" repeated over and over. The B channels never come up. There are no errors in any of the logs, zttool, or the wanpipe tools. Intense pri debug output: < Unnumbered frame: < SAPI:

Hi, I'm having problems with a new ISDN PRI in a new server. The cable is connected and the E1 modem seems to have issues with syncing (blinking light on the modem). versions: CentOS 6, asterisk 1.6.2.20, dahdi 2.5.0.1, libpri 1.4.12 ------------------------------------------------------------------------------------ dahdi show status T4XXP (PCI) Card 0 Span 1 RED 0

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?

Hi guys, We are experiencing a problem with a T1 PRI connection. After trying a number of variations in the configuration files, the behavior is always the same: no B channels come up and the D channel doesn't appear to be working well. We can see there are AT&T Maintenance messages being exchanged by asterisk and the provider, CONNECT and CONNECT ACKNOWLEDGE, but that doesn't

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

On Thu, 2006-03-02 at 11:42 -0600, Jordan Novak wrote: > Does anyone have a way to do wake calls? > > > > Jordan Novak > > Communications Technician > > Logistics Health Inc. You could use cron and /var/spool/asterisk/outgoing scripts to dial numbers, etc... > Can you elaborate, I am fairly new to Linux and a phone guy to boot. I am looking for a way for the

I have a working system with asterisk 1.4.26.2 libpri 1.4.1 and zaptel 1.4.12.1 With a digium TE205p. I am trying to update to libpri 1.4.10.2. When I do, incoming calls work but outgoing does not. When I do this I "rm /usr/lib/libpri*" then just install libpri-1.4.10.2 as normal. I then do a make clean in asterisk and make distclean ,then configure, make and make install. I do

I have an application where I need to send outbound prerecorded messages. The Asterisk "call file" process works fine if I am sending the call via SIP or IAX, but not via ZAP over a PRI channel. The destination device (my cell phone) never rings. The only unusual thing I see is on the fifth line of the "full" log, below, "channel.c: Don't know what to do with

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

hello, I have a Junghanns QuadBRI card in my asterisk server. I'm able to dial & connect to local numbers through the ZAP interfaces however when I try to dial national numbers with the according area code the connection fails, an intense BRI debug is shown below. The error being Ext: 1 Cause: Unallocated (unassigned) number (1), class = Normal Event (0) about half way through the

Hello, I got a Problem with my HFC Card, I start my "asterisk -vvvvvvvvvvvvc" The console comes up: ---------------snip---------- Asterisk Ready. *CLI> ---------------snip---------- Setting up debuglevel for span 1 ---------------snip---------- *CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 ---------------snip---------- Console output:

I wonder if anyone has come across this odd behavour with a T1 PRI using NI2 signalling from a Nortel switch. Sometimes, when bringing up a PRI trunk, a channel gets into a state where asterisk can't request a channel, and gets reason 0, but the channel is not busy. The only thing so far that clears this state is to make an incoming call to the channel, which succeeds. After that, outgoing

We are trying to send caller ID NAME information over a Telus PRI in Alberta. The PRI tech says that he sees the NAME information, and for calls over the same network, that NAME info should be reaching the receiving station, but it is not. The technician was stumped. I suspect there's something specific that I need to do to make it work, since many PBXs can do this. The switch is a

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

I'm not a PRI expert and therefore don't know what this debug stuff means for PRI, so if anyone can help me here... I'm running the latest libpri and zaptel from CVS. Keep in mind that everything works fine when using the STABLE libpri and zaptel. I am NOT running CVS asterisk. I am running 1.0.6. asterisk*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203