similar to: Can Asterisk bridge between a SIP client and a Cisco Call

Hi, This is probably outside what Asterisk is intended for, but I'm hoping it can help. I need to make and receive calls through a Cisco Call Manager server that I have no control over. I have to use a Cisco soft phone (Cisco IP Communicator), which only runs on Windows. But I'm on Linux. CCM is apparently capable of supporting SIP and H.323 interfaces, but they won't provide

Hi, I've got a CCM ( Cisco Call Manager ), with a Cisco Unity VM server and about 45 SCCP phones on the ccm, and 200 users on unity. we want to migrate all users to IP Phones to ditch our ancient phone system. I would love to get Linksys-Sipura SPA-941s for the 150 users not on IP phones yet and run sip to an asterisk server, but have their voicemail on Unity. these phones are $150 each,

It can be done. 1. Setup a new Vm profile on CCM with a mask of XXXX 2. Setup a CTI route point: a. Set the directory number to a pattern. I use *27XX but any pattern that you can send from * is good, ie. 88XXX b. Set the VM profile to the newly created profile c. Set the line to forward all calls to VM 3. Change the dialplan in * to append the extension called to the

Hi, I have the following config: [7960] <--skinny--> [Cisco CCM] <--SIP_trunk--> [asterisk] <--SIP--> [X-lite] Is there a chance to avoid the RTP stream from passing through the Cisco CCM ? I would like to have all RTP handled by the *. This is just a testbed, for a larger project. What I want to achieve, is actually this: [Cisco Phone] <--skinny--> [Cisco CCM]

Here's the problem, I upgraded all of my 7960 phones to SIP. Now my boss wants to carry his phone with him between offices. The other office has CCM which is set up for Skinny. Now I have to put SCCP back on a 7960 phone and it won't take it. Does anyone have an example of config files for sccp. Are they the same as config files for SIP? I've never had to go back to Skinny once I

Hi Siggi, > > 7960 and then "Call Ended" on the Display (curious about that !!!). > > That seems to be normal for the 7920. I've sniffed the registration > procedure with Cisco's newest 3.3(3) CallManager (+patches), and it's > doing the same thing. Maybe that's some odd way of testing if the > CallManager ("CCM") really works... >

Hi All, Thanks for every one who helped me on this regard. I think i was able to rictify the problem. what i did is remove callprogress=yes usecallinpres=yes and restart asterisk. Today i didn't report any drop calls. Many thanks for Eric. :) I hope this situation will continue. Regards, Vidura. On 3/8/07, Vidura Senadeera <vidurased@gmail.com> wrote: > > Hi, > >

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

Hellow, * I have a problem with dial up signalling. currently I have configured asterisk server and E1 card to ISP. then other side I am having ATA to PC for connecting internet through DialUP connection. is it possible and please send me the procedure how I can do it ?? * ISP< <-> Asterisk <-> ATA <-> DIALUP -- Thanks & Regards, Vidura Senadeera, Sri Lanka.

Please forgive me my ignorance ... I've spent two days trying to find out something about the format of the default configuration file, which CCM produces. The only example I have so far is the one from the chan_sccp source. There were tons of references on entering the callmanager commands on a cisco command line - which I don't have (don't need thanks to chan_skinny + chan_sccp).

> Hi Gareth Blades & Doug, > > Thanks so much for for the feedback. I have searched on lot of documents > but couldn't able to find clear answer regarding it. > > I hope you guys replies are very much help all in aterisk community. > > > Thanks & Regards, > > Vidura Senadeera, > > Network Engineer, > > Debug Solutions > > Sri Lanka .

Dear All, I would like to get community's feedback with regard to RAID1 ( Software or Hardware) implementations with asterisk. This is my setup Motherboard with SATA RAID1 support CENT OS 4.4 Asterisk 1.2.19 Libpri/zaptel latest release 2.8 Ghz Intel processor 2 80 GB SATA Hard disks 256 MB RAM digium PRI/E1 card Following are the concerns I am having I'm planing to put this asterisk

Hello, I'm trying to connect Cisco Call Manager 3.3 with Asterisk using H.323 Gateway. When I place call from a SIP phone registered at Asterisk to SCCP phone at CCM I can hear the voice in both directions. But when I call from SCCP phone at CCM to SIP phone at Asterisk the voice goes from CCM to Asterisk only. All devices have real IP-addresses - no NAT is used. Asterisk console does not

Hello, I can use directed call pickup using pickup application (between sip, iax, skinny cals), but unable to pickup call that is ringing on phone behind h323 gateway (using original h323 channel in asterisk), is this even suported? thx PJ exten => _*7.,1,Pickup(${EXTEN:2}) console log, when trying o pickup ringing line 324 (h323), from skinny phone (953) -- Executing

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

Hi, I am developing a call recording application on Asterisk 11.2 and have this configuration in my dialplan: [macro-ccdev2-rec] exten => s,1,MixMonitor(${ARG1},b) [outgoing-originate] exten => _X.,1,NoOp(Will send call to ${EXTEN}) exten => _X.,n,Dial(SIP/${EXTEN}@x.y.z) [outgoing-originate-rec] exten => h,1,Agi(agi://localhost/ajpbx.agi?path=uploadrec&callid=${CC_CALLID})

I've got an Asterisk to H323 bridge working... but I'm having a few problems.. I got everything working by setting up with the Asterisk box as a gateway in CCM. I've got two issues.. 1. If I call off net.. (Asterisk -> CCM -> Cisco 5300(I think) -> PRI) the calls will proceed.. connect, and I get about 4-5 seconds of RTP and * tells me the remote end terminated my call. I

Some of you may remember back in May the thread on using Asterisk as a voicemail server for a Cisco Callmanager system. My own Callmanager system is integrated into an Asterisk server for voicemail (and other things). Back in May I was using H323 for integration, but since I've upgraded to CCM 4.1 I have switched over to SIP. The integration with H323 required using Call forwarding to send

Hi, The examples for making a bootable usb key using extlinux just transfer a live cd to usb. To me, this misses the advantage of usb keys (other than size), that they are writable. I would like to have a full linux install on a usb key and be able to boot it using extlinux. This way I can install new packages and make other changes without jumping through squashfs hoops. Is there reason why

Hi, I was able to work out SIP trunk between Asterisk and CCM 4.x without any issues. Whereas SIP trunk in CCM 5.x is not working with Asterisk. Asterisk is sending OPTIONS messages to CCM 5.x for which CCM is not replying. For the same reason Asterisk is marking it as UNREACHABLE. Anybody got Asterisk and CCM 5.x intergation working. How can I fix the problem which I'm facing with CCM 5.x?