similar to: BRI/ISDN, misdn.conf/misdn-init.conf, OpenVOX B100P and Etisalat in Dubai

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Dear All, We have a customer who is opening a new office in Dubai and we know that VoIP is blocked over there. Has anyone a solution to getting VoIP back out (we want interoffice calls back to the UK)? We we're thinking of IAX trunking, but not sure if that is blocked or just SIP etc. A VPN works, but is not great. We have seen: http://www.speed-voip.com/voiceguard.html At the moment it

Hello, I'm trying to set up a b410p rdsi card, and I'm having problems getting it up. I followed the instruction on asteriskguru and everything seem to be fine but all leds on the card are in red. [root@rdsipbx ~]# uname -a Linux rdsipbx 2.6.15.7 #2 Tue Jun 5 16:37:07 CEST 2007 i686 i686 i386 GNU/Linux [root@rdsipbx ~]# dmesg |grep Digium HFC-multi: card manufacturer: 'Cologne Chip

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I am struggling to get plain Cologne chip cards to run in NT mode, runs nice in TE mode despite the error message: login as: root root at 192.168.2.22's password: Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50 Welcome to Elastix ---------------------------------------------------- misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hi all, I have a "Cologne Chip Designs GmbH ISDN network controller" and I want to terminate voip calls via this ISDN card. My question is: How I must to wire the ISDN equipment with my ISDN card? With normal cable or crossover? How I can to check if ISDN card is linked with ISDN equipment? In this moment I have 1:1 cable between ISDN's, the mISDN is installed and "misdn

Working in Dubai Dubai in the United Arab Emirates is one of the world''s fastest growing employment hotspots in the world. Up to 20 new companies establish themselves in the emirate''s free trade zones every week and since 2002 some 650 companies have registered in the Dubai Media City free trade zone alone. http://2site.com/zpcyag When to Replace Brake Pads Worn brake pads

Hello All We need to connect our client's offices located in Dubai and Pakistan. Suggest us some economical solution. -- Kashif Naeem Business Development Manager Hadi Telecom www.haditelecom.com Cell: +92 (0)345 4226006 Office: +92 (0)42 5692766 Email: kashif at haditelecom.com MSN: kashif__naeem at hotmail.com Gmail: meet.kashif at gmail.com Skype: kashif.naeem 302 Y Commercial Area,

We have ISDN PCI Adapter from Billion(using mISDN). When we connect it to the PSTN the incoming calls are OK. When we try to make a call we can't do that because the ISDN port is Down: CLI> misdn show port 1 BEGIN STACK_LIST: * Stack Addr: 40400001 Port 1 Type TE Prot. PMP L2Link DOWN L1Link:DOWN Idx: 0

Greetings! Anyone here who can refer me to someone who is looking for a system or network engineer for a company based in Dubai, UAE? I have a pretty good experience in networking R&D and ISP environment and have familiarized my self with configuration of various network services (dns, web, sql, ldap, email), network monitoring tools, mrtg, cacti, nagios, netflow, ids/ips etc. BSD, Linux,

Hi, All I am looking for Suppliers/resellers from Dubai - UAE to buy some VoIP products and Digium's TDM cards. could some one send me some contact information in this regards?. mainly I want to buy Hardware SIP phones, VoIP gateways and DTM cards (FXS). Thank you Kumara

Hi! I'm trying to set up an asterisk based PBX with a TDM400P +2 FXS +2 FXO modules in UAE/Dubai for home switching / voicemailing. I am using the card Asterisk/Zaptel 1.4.0. I want to include a special route when a certain caller calls into via PSTN. The problem is that I cannot detect the Caller ID. I tryed various setting (cidsignalling, cidstart) in my zapata.conf, here is the last

The codes, tools, exploits, slides and other presentation goodies from HITBSecConf2008 - Dubai are available for download! You will also find a 'bonus download' of the live recording of DJ Negative's set from the HITB Post Conference Party at the URL below :) http://conference.hitb.org/hitbsecconf2008dubai/materials/ The official photos from the training, conference and party have

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no