similar to: SIP *8 Pickup Problem

Hi! What are the typical ways to work around the 64 groups limit? thanks klaus

Hi! I have the following problem with Asterisk 1.4.23: ATA w/ T.38 Asterisk ATA w/o T.38 --------INVITE--------> --------INVITE--------> <-------200OK---------- <-------200OK---------- --------ACK-----------> --------ACK-----------> --------INVITE

Hi! I've went through the READMEs and could not answer this question: During installation, the Setup program asks: Would you like update/upgrade wanpipe drivers? (y/n) For a pure Asterisk TDM installation - is it required to patch the kernel or is this only when using the sangoma cards as WAN router? regards klaus

Hi! Is it somehow possible to evaluate the SIP response code inside the dialplan? I have an Asterisk server which forwards requests to various PSTN gateways with SIP. If the Dial() attempt is not successful I want to differ at least these 3 options: - called destination is busy (486): e.g. activate auto-redial - called destination does not exist, unassigned number (404) - gateway is broken,

Hi all, Is it possible to install more than 1 asterisk in a single server? If yes, what do I need to set and take care? Rgds, ango

Hi! Since some time the download of the newest Asterisk does not contains the version number anymore, but is just called "asterisk-1.4-current.tar.gz" This gives me a tarball where I do not know the version without looking into the tarball. Thus, IMO it would be very useful to switch back to old schema war the download contained the version number. Thanks Klaus

Hi! I am looking for a tool (application or webinterface) which shows me the current status of an Asterisk server, e.g.: - Status of the SIP peers (registered/offline) - current incoming and outgoing calls - start-time, numbers, some history - history (calls stopped in the last 15 minutes, who hang up?) - should be possible to link those calls to the relevant SIP peers -

Hi! All the AEL examples have a semicolon after the closing curly bracket, e.g: context test { 1 => Hangup(); }; but without ; it works fine too, e.g: context test { 1 => Hangup(); } So - what is the reason for the ; after the closing curly bracket? thanks klaus

The problem: T100P connected to an Adit600. Channel 1-16 are FXS, 17-24 FXO. I have Zap/24 in callgroup 3 and Zap/1-16 in pickupgroup 3. When a call comes in on Zap/24 I cannot pick it up with *8 from Zap/1-16. *CLI> show version Asterisk CVS-04/27/04-23:48:08 built by root@tuck on a i686 running Linux The zapata.conf and extensions.conf are located here:

Hi! I have a setup with Asterisk in front of a PBX connected with ISDN to the PSTN and to the PBX. This Asterisk (a old 1.2 instance) is doing ENUM for outgoing calls and allows incoming calls per SIP. Recently the IP connectivity for this location was down the whole telephony was down too - not even incoming calls did work. This is really strange as incoming calls from PSTN are routed

I'm using the Debian Sarge package of Asterisk - 1.0.7 + bristuff. When I call from a zap channel or a SIP phone to another SIP phone, then dial *8 from a third SIP phone, I get 503 Service Unavailable on the third phone and I get this at the Asterisk console: Jun 28 09:01:24 DEBUG[16774]: res_features.c:1709 ast_pickup_call: No call pickup possible... Jun 28 09:01:24 NOTICE[16774]:

Hello I have a Junghanns ISDN BRI card for incoming calls and use SIP Polycom IP300 phones. My config files look like this: features.conf pickupextn = *8 zapata.conf context=frompstnisdn group=1 callgroup=1 pickupgroup=1 I also edited sip.conf like this: group=1 callgroup=1 pickupgroup=1 But on internal and incoming calls if I dial *8 from any phone I cannot pickup. Do I need to add

Hi! I wonder why users.conf generates a SIP user and a SIP peer? Why is it not possible to set type=... in users.conf? (Asterisk 1.4.22) thanks klaus

Hi! IIRC there was an announcement some time ago that it is possible now to make conferences without the need for DAHDI anymore - but I can not remember the name of this feature anymore, and google didn't solved my problem. Thus, any references to this new system are appreciated. thanks klaus

Hi, I have been trying to workout how to use the call pickup. So Far, I have the following in zapata.conf [channels] signalling => fxo_ks context => local pickupgroup=1 callgroup=1 channel => 1-3 When I dial *8# all I hear is busy tone. What have I missed? thanks Jay.

Should setting a namedcallgroup & namedpickupgroup supersede numeric callgroups and pickupgroup ? I've got 5 peers on my 13.7.0 box, Three of them have a namedcallgroup & namedpickupgroup of 'kiniston' and Two of them have a namedcallgroup & namedpickupgroup of 'sanday'. I'm not specifying a numeric callgroup or pickupgroup so all the peers are defaulting to

Hi there, it appears that call pick-up only works _within_ a technolgoy, i.e. with a SIP phone when another SIP phone is ringing. Is that correct, or is my configuration faulty? * Case 1: SIP phone 1 ringing - SIP phone 2 can pick the call up with *8 We are happy! :-) * Case 2: IAX phone ringing - SIP phone can't pick the call up: NOTICE[10250]: Nothing to pick up * Case 3: SIP phone

Hello, I have set pickupgroup and callgroup for zap, sip and iax2 devices. Everything is working good with zap and sip and between these two. Iax2 pickupgroup and callgroup seems to be broken. I cannot pickup a call to IAX2 from SIP. Is there somewhere a bug ? I am running: Asterisk 1.2.9.1 Bartosz

Hi! I want to use Asterisk as load generator to test quality degradation with increased load (e.g. testing other SIP equipment or IP-links). Is anybody aware of such a setup with Asterisk - is it possible to get RTP statistics out of Asterisk (e.g. jitter, packet loss, reordering ...)? Thanks Klaus

Hi All; I am facing a problem that always the users confused and connect the telephone line coming from the telephone service provider to the FXS port and cause it to be damaged, specially if the card was 2 fxs and 2 fxo, so they make mistake and connect the line to fxs while it should be connected to fxo. What is the solution for this disaster? Regards Bilal