similar to: Asterisk BLF to Cisco CME

Hi all, I'm trying to trunk my asterisk with a cisco cme 3.3 using h323. Cisco conf: dial-peer voice 8 voip destination-pattern 2... session target ipv4:<asterisk ip> codec g711alaw no vad h323.conf [general] port = 1720 bindaddr = 0.0.0.0 ;tos=lowdelay ; disallow=all allow=alaw allow=ulaw allow=gsm context=from-internal extension.conf [from-internal] exten =>

Hello We have integrated cisco callmanager 4.1 with asterisk and we can dial from cisco to asterisk but we're getting an error if we call from asterisk to callmanager. This is the error I'm getting anybody can help me? Verbosity is at least 3 -- Executing Dial("SIP/2234-e084", "SIP/cme-pbx/4455") in new stack -- Called cme-pbx/4455 -- SIP/cme-pbx-25ae is

I was thinking about complicating my Voip setup by adding CME. I found this example here: http://www.voip-info.org/wiki/view/Asterisk+Cisco+CallManager+Express+Integration and here: http://www.pasewaldt.com/cme/cme_index.htm Would anyone like to comment on their experiences using CME with Asterisk... I would like one of my Cisco phones to remain SIP connected directly to my Asterisk system. The

Hi folks- I'm working on getting a test Call Manager Express system working with Asterisk. My plan is to have * support all the voicemail boxes for the CME/SCCP phones. Right now, I can call from a SIP phone to a SCCP phone and back fine. Calls go from Phone->CME->*->Phone and the reverse. Voicemail works for my SIP phones, but does not work for the SCCP phones. I tried to follow

Hi All, I'm just posting this questions to both forums as its related to both. In hope to get some help on below issue: Asterisk 1.4.x CCM = 4.x CME = 4.x codec = g711ulaw Here is my setup: 600X Phones ----> Asterisk ---- SIP Trunk ----> Call Manager -----> CME -----> 461X Phones 461X Phones ----> CME -----> my dial peer points to Asterisk IP for 600X Phones so in

I am starting to work on a similar solution, but with full call manager rather than CME. I am going to use Asterisk to accept POTS calls through PCI FXO ports (winmodems) and then forward the calls through to call manager via SIP. I don't have my FXO cards yet (waiting for UPS man!!) but I have * talking to the CM through SIP just fine. I am testing with the Cisco softphone, connected as a

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi folks, I would create a structure like this: external sip server \ external sip server |-----| Asterisk |------| Cisco CME |-------| ip phones | external sip server / I would use Asterisk as SIP client for some SIP accounts on external servers ... then register those via H323 (if possible; skynny?) on Cisco CME ... Then I would use Asterisk

Hi All, We have a Cisco CME linked to our Asterisk PBX (named 'epstein'). Off said PBX we have numerous other PBX's, some IAX and some SIP. On a call placed from CME (SIP) to 'epstein' it all works fine except for a few quirks. When calling through epstein to an IAX peer we get '100 trying' followed by '180 ringing' sent back down the SIP leg to CME.

Stephan, Ok, I'll re-state the problem... I have two devices that I want to talk to each other: 1. an Asterisk PBX 2. a Damm Cellular TETRAFLEX digital radio system (www.damm.dk) both devices are effectively "gateways" because they have many subscribers behind them. The Damm Cellular system controller is based on Windows-XP Embedded and its sub-systems used the OpenH323

Hello All, I've been trying to get BLF working with Asterisk 1.6-LatestBeta, and My Cisco 7970 (Latest SIP Firmware). Has anyone successfully completed this? I got the patch to merge in from http://www.voip-info.org/wiki/view/Asterisk+Presence+for+Cisco+79x1+Phones With a bit of hackery to that code, it successfully compiled chan_sip for me. So, With 1.6 we have TCP Enabled on Asterisk,

I found with some more testing that you have to setup a 5 digit number (or something longer than your phone extensions) to make the voicemail work. Now the trick is making the MWI work. Rick -----Original Message----- From: Lull, Rick Sent: Friday, July 15, 2005 3:55 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: VM on * for CME Install Hi folks- I've

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi folks- I've got to the point of trying to configure voice mail on the * box for the SCCP/CME phones. The phone can call the voicemail number (8500) and I can hear Allison's voice. Attempts to punch in a voicemail box number or password don't seem to register; keypad presses don't seem to be heard by the * box. The CME configuration has the 'dtmf-relay rtp-nte' command

Hi, Does anyone have any experience with a Cisco 7961 + 7914 Operator Console setup and speeddials/BLF on Asterisk 1.4? Would appreciate feedback if this works reliably. I have a 7961 on skinny registering on an 1.4.19 box with chan_sccp and speeddials work fine so that part seems ok. I have no experience with the BLF part. >From googling around it seems that BLF on the 7914 only works with

Hi all, I have 2 asterisk box connected with IAX trunk. One box have connected a SIP phone and the second have a TDM card with one analog phone. When from SIP phone I try to park the call from analog phone with #700 the call is correctly parked but in the second asterisk I see this log: -- Executing Dial("Zap/2-1", "IAX2/CTM1/STI1|30|rjtT") -- Called CTM1/STI1 --

Hi, I was wondering if anyone stumbled upon the correct event in a sip NOTIFY (from a SUBSCRIBE) to make the BLF lamps on a Linksys/Cisco SPA9xx/5xx go yellow? I'm trying to differentiate between "On the Phone" and "DND" with the BLF. Thanks. -- James

I have been trying to get the 7970 (running SIP firmware) to display presence information about other extensions. Thus far, I have been unsuccessful. Does anyone have BLF working on the SIP-loaded 7941/7961/7970/7971? I have been using the following as a guide for my work: http://www.voip-info.org/wiki/view/Asterisk+Presence+for+Cisco+79x1+Phones I have successfully implemented every step

ive had enough of cisco unity and microsoft exchange and im looking for alternatives to our voip system. right now, we have 3 cisco callmanagers, 1 cisco ip icd system, and 1 cisco unity voicemail system. all phones are cisco 7940/7960's and some ata186/188's. voice gateways are cisco vg200's with pri cards (5 total). im running h323 on the gateways and phones are of course

I have a smartnet contract for this phone, and have searched high and low for this file on the Cisco website. I need: United_States/7960-tones.xml English_United_States/7960-font.xml Every road seems to lead to the Call manager express downloads... I don't have a CME, so that's basically useles. Can anyone point me in the right direction? Mikel

First, the scenarios: Call placed from Boston to locally configured Asterisk Meetme extension: Cisco 7941 <-SCCP-> Cisco 2821(CME,Boston) <-SIP-> Asterisk(Boston) Call placed from Boston to European Asterisk Meetme extension: Cisco 7941 <-SCCP-> Cisco 2821(CME,Boston) <-SIP-> Cisco 2821(CME,Europe) <-SIP-> Asterisk(Boston) In the 1st scenario, everything works