Displaying 20 results from an estimated 2000 matches similar to: "Fw: Re: mISDN BRI Asterisk 1.4"
2009 Jan 13
3
mISDN BRI Asterisk 1.4
Good Evening,
The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX
Everything has compiled successfully and the BRI card has been detected when mISDN is started:
# misdnportinfo
Port 1: NT-mode BRI S/T interface port (for phones)
-> Interface
2009 Jan 22
0
Fw: Re: mISDN BRI Asterisk 1.4
Have you got termination set correctly?
I have a B410P working with 2 x NT and 2 x TE ports successfully.
I had to turn the 100ohm termination on on the NT ports (even though I
have them set as PTP in mISDN.conf).
HTH
-->> -----Original Message-----
-->> From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-
-->> bounces at lists.digium.com] On
2009 Mar 12
2
BRI/ISDN, misdn.conf/misdn-init.conf, OpenVOX B100P and Etisalat in Dubai
Hi All,
We've got msidn configured:
Port 1: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1 (Euro ISDN)
-> childcnt: 2
--------
mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060)
iend(0x8fd5060)
and running on Asterisk 1.4.21.2:
pbx*CLI> misdn show stacks
BEGIN STACK_LIST:
* Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0
2009 Jan 24
1
Which policy for ISDN BRI support in NT/PtMP ?
Hi,
As you may know, these ISDN BRI features are very important here in Europe
as ISDN Basic Rate Access is very popular among Small & Medium Entreprises.
I don't really know why but it seems that in many countries, default is to
install small PBX using Point-to-Multipoint (PtMP) mode as opposed to
Point-to-Point (PtP) which is the norm for PRI.
So basically, in several countries, SME
2012 Jun 21
2
Asterisk 10/1.6.1 and Dahdi/Libpri compatilities in BRI /PtmP
Hi,
After an upgrade, I discovered yesterday strange things I would like
to share here.
Basically, I'me comparing platforms:
The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk
1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3
and 2.5, I think).
The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk
10.5.1, Libpri 1.4.12, Dahdi 2.6.1.
Both are
2009 Sep 01
0
mISDN NT mode config setting
Hi,
I am struggling to get plain Cologne chip cards to run in NT mode, runs
nice in TE mode despite the error message:
login as: root
root at 192.168.2.22's password:
Last login: Tue Sep 1 23:09:24 2009 from 192.168.2.50
Welcome to Elastix
----------------------------------------------------
misdnportinfo
Port 1: TE-mode BRI S/T interface line (for phone lines)
-> Protocol: DSS1
2009 Mar 11
3
Digium B410P: misdn v1 or misdn v2 or dahdi + asterisk 1.6 ?
Hi,
Until now I've been using my Digium B410P cards with misdn 1.0.x.
I would like to upgrade my systems and am now wondering which is the "best" route to take:
- use the latest release of misdn v1
- upgrade to the latest "stable" kernel and use the built-in misdn v2
- use misdn v2 as a seperate package (disable misdn in the kernel)
- use dahdi's support for misdn
2005 Feb 04
1
*, BeroNet BN4S0 and misdn - problems
Hi,
i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module
is loaded with option:
type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf
and the fourth port is connected to an ISDN PTMP (MSN) port.
Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ?
Can anyone give me a hint ??
misdn debug messages follows:
lib: NEW_CR Ind with l3id:80001
2012 May 09
5
Belgian BRI (euroisdn): what to use for a B410P
Hi,
I'm experiencing difficulties to get a B410P running with Asterisk
10.3.1 and DAHDI 2.6.1.
Am I supposed to use DAHDI for this card and ISDN BRI for my country
(Belgium)?
thx,
BC
2013 Jun 06
1
Which dahdi/libpri combo for BRI/PtmP ?
Hi,
I need to rebuild a system which has 4 BRI ports and is connected to
Point-to-multiPoint lines, in a country where telco often "drop lines for
energy savings".
I'm planning to use latest 11.4.0 asterisk version along with dahdi and
libpri (no misdn).
Which version are recommended for Dahdi and Libpri ?
My main requirements are, beside having calls coming in and out:
- keep a
2008 Dec 17
3
libpri and NT-Point to multi-point
Hi,
At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point
to multi-point mode.
Here (France), most small PBXes are connected to ISDN through BRI trunks in
PtmP (don't know why but it seems the general case).
So this NT-PtmP function would be very helpful to easily slide an Asterisk
box between an existing PBX and the network.
Does the same case apply elsewhere (UK,
2004 Jun 07
6
chan_capi and DDI (Anlagenanschluss)
Hi all !
We have 3 NTBAs which are all going to our existing PBX. Our areacode is
06003 and our DDI enabled number 9141.
I want to exchange that PBX with Asterisk, but still struggle to get it
working.
My CAPI.CONF is currently like this:
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.800000
txgain=0.800000
[interfaces]
context=in-capi
msn=60039141
incomingmsn=*
controller=1
2010 Sep 28
3
ISDN - Busy signal on 3rd call
Hello,
Following my first mail about this issue [1], I think I know now what
the problem is.
When I have both lines being used and a third call comes in, the person
calling doesn't get a busy tone, he gets something like line unavailable.
I've been debugging mISDN and I think the reason is because asterisk is
sending the release cause as 0.
P[ 3] --> channel:0 mode:TE cause:0
2008 Dec 01
1
[SPAM] - Re: [SPAM] - Dahdi, b410p and looping from 1 port to another - Email found in subject - Email found in subject
Apart from you were dialling out on your inbound context and
vice-versa.
The best advice I can give now is to change to mISDN - as this
is proven to work with v1.4 and v1.6.
Actually - have you tried putting the 100ohm termination on for
your NT port?
I need to do that with mISDN as it only allows ptmp for ISDN
extensions.
Cheers
Andy
-------------- next part
2007 Jul 17
1
chan_isdn with HFC-compatible
hi list,
I'm currently trying to get Asterisk running with an HFC-compatible ISDN
card (no-name product, but supposed to work with Asterisk according to the
packaging). the ISDN-card is connected to a alcatel ISDN-system where it
should act just like a normal ISDN-phone.
I went with http://www.misdn.org/index.php/MISDN_with_Asterisk and installed
the package from beronet.com including:
2008 Dec 01
2
[SPAM] - Re: [SPAM] - Re: [SPAM] - Dahdi, b410p and looping from 1 port to another - Email found in subject -Email found in subject - Email found in subject
The DAHDI docs actually include the 'steps' that used to be in Zaptel's
'make b410p'. These steps involve downloading and compiling mISDN. Why
re-invent the wheel?
Just a thought :-).
As for the 100ohm termination bit - it's simply changing a couple of dip
switches on the b410p card (as described in the manual).
Andy
-----Original Message-----
From:
2006 Mar 03
10
MultiBRI in Australia - found one - maybe
I may have found a source of an A-Ticked HFC 4BRI PCI adapter in
Australia, and will be testing one next week if all goes well. I don't
want to post the details of the reseller online unless invited to do so,
so if nobody replies and says they are interested then I won't :)
I'll follow up once I've tested it.
Let me know if you want the details.
James
2009 Jan 05
1
B410p, Ast1.4, France Télecom Numeris Double T0 problem
Hi.
When I call my RNIS numbers (with a mobile phone for example), I can
see 2 incoming calls on the IPBX, which should not happend.
I'm not sure if it's a problem with the telco France Telecom and their
ISDN setup, or if it's a problem
with the MISDN driver on the IPBX itself.
I'm stuck ...
Any advices for troubleshooting that?
Someone provide working configuration files
2009 Jan 07
3
mISDN compile problem
Hi,
I'm bumping on this :
cd /usr/src
wget http://www.misdn.org/downloads/mISDN.tar.gz
tar xvf mISDN.tar.gz
cd mISDN-1_1_18
make
<snip>
In file included from
/usr/src/mISDN-1_1_8/drivers/isdn/hardware/mISDN/core.h:9,
from
/usr/src/mISDN-1_1_8/drivers/isdn/hardware/mISDN/avm_fritz.c:20:
/usr/src/mISDN-1_1_8/include/linux/mISDNif.h:791: error: field
2009 Jan 08
2
Could you compile mISDN 1.1.8 on Lenny ?
Hi,
Before diving into this, I would very pleased to know if someone could yes
or no, successfully compile mISDN 1.1.8 on Lenny (latest RC1 or beta2
version) ?
Regards
After a fresh install on Lenny, I can reproduce at will :
apt-get install build-essential linux-headers-2.6.26-1-686
cd /usr/src
wget http://www.misdn.org/downloads/mISDN.tar.gz
tar xvf mISDN.tar.gz
cd mISDN-1_1_8
make
....