similar to: PAP2T provisioning

Hi there, We have plans to install an office (not call center) with the following setup: 200 linksys 942 phones (sip + g711) on a LAN a server with a dual port E1 sangoma and a remora card with 4 fxo modules. So far when we want to setup a linksys phone, we need to use the http interface of each phone, disable/enable a lot of things and plug it into the network. this is not the best scenario for

Surely there must be someone here who can help me with this problem. I have spent weeks trying to get this damned service to work with no luck. I have incoming calls working, but no outgoing. If get outgoing working then incoming don't work. I have sent this problem to this list a couple of times with little or no response, and I _really_ need some help to sort it out. I have an asterisk

Hi Everyone I think PAP2T supports DynDNS and other Dynamic DNS providers. I have a box that needs to be secured at all times. Currently it's not connected to the internet. If it were connected, I would have iptables block any and all traffic from outside but I want a single device - Linksys PAP2T - to be able to connect back to the server. That is a stand alone device and doesn't support

Hello, I have just received an MGCP Phone for test purpose and I can't place a call from my MGCP Phone. I can call my MGCP phone from a SIP Phone. Here is my mgcp.conf: ; ; MGCP Configuration for Asterisk ; [general] ;port = 2427 ;bindaddr = 0.0.0.0 ;[dlinkgw] ;host = 192.168.0.64 ;context = default ;line => aaln/2 ;line => aaln/1 [192.168.10.10] host = 192.168.10.10 context =

Hi all, Is it possible to send a SIP header to a PAP2T or SPAxxxx and cause the device to automatically answer? I can do this with my Polycom phones and would like to do it with my ATA's. Any ideas? -- Take care and have fun, Mike Diehl.

i have the problem in the hardware linksys pap2t, I am install asterisk with asterisk-gui and work fine but the hangup the phone (linksys pap2 t), no tone and sound like tu,tu, tu , tu , tu , tu , tuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu what is the problem with phone ??? add param special??? Note: i am mark number phone and wait ... sesonds and call. thank you. -------------- next

Here is Mexico the phone company uses a DSL router from 2Wire which in my opinion is quite bad. I am having problems getting PAP2T adapters connected to Asterisk using these routers. They connect fine but after about 5 minutes I get a message on the Asterisk console that the ATA is unreachable. So far the only way I have found for the ATA to stay connected more than five minutes is to put it in

Does anyone know how the Linksys PAP2T ATA's can be mass provisioned? Documentation seems to be sketchy, even on the Linksys web site. Thanks, Doug. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070607/3f90695c/attachment.htm

I'm trying out a Linksys PAP2T-NA. Calling out works great, no problems there. Calling in, though, the phone doesn't ring. Caller ID shows up, I can pick up the phone, and the call is connected, but no ring. I've tried it on two analog phones, same behavior. Suggestions? Asterisk SVN-branch-1.2-r31555. - James Moore

Hi Folks, I know the PAP2T-NA has a jitterbuffer.... however, it seems to be adaptive, which is fine for most situations... however, is there some way I can either: A) Specify how long it waits before it starts to shrink? B) Specifiy a fixed sized jitterbuffer? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all. I received a PAP2T-NA from a potential customer to see if I could get it configured for testing. I plugged it into my network and plugged a phone into it and attempted to do a factory reset from the handset. I pressed "****" and got NOTHING! Just silence. So, is this TA a brick? Or is there additional voodoo that I'm not aware of? Mike.

I'm considering a situation where I buy about twenty ATA devices. I've played with the Linksys / Cisco PAP2T, and got that working fine with some inbound and outbound faxing. The web GUI was okay. I'm seeing prices around $45 to $50 for this thing. It comes with two FXS ports, but I only need one FXS. I've seen the Grandstream Handytone 286 online. It looks promising as an

Hi all: when i make a call from linksys pap2t to an asterisk server a fake ring is heard some times ,but when sending calls between 2 asterisk servers through sip no fake ring is heard but real one. any suggestions please. _________________________________________________________________ Windows Live?: E-mail. Chat. Share. Get more ways to connect.

I was having problems getting a Linksys PAP2T-NA to work with Pitney Bowes mailing station so it could use its modem to dial home and download postage/software updates. After scowering the web, I couldn't seem to find a definite how to article on what settings were needed. I finally came up some settings by combining the information from various places around the 'net. I have typed out

Hi all, I'd like to know how I can turn off the "splash ring" voicemail waiting indication on a PAP2T from the provisioning XML file. I can do it from the web interface, but I need to do it on "a lot" of machines.... TIA, -- Take care and have fun, Mike Diehl.

I've got a PAP2 that I've got working with asterisk. At the moment, its configured so that when a phone is picked up on it, it connects to Asterisk. My hope is that I can let Asteirsk handle the entire dialplan, including dial tone generation. What would my context in extenstions.conf look like for this sort of dialing. More accurately, how can I get Asterisk to generate the dial tone on

OK this is the RTFM question of the day but I need a sanity check. I have 2 Astra 51i phone and a linksys PAP2 on a single DSL connection. 2 Aastra 51i---------| |-NAT on dsl moden--(Internet)--Asterisk PAP2t----------------| The DSL modem/router which has QOS set for the src and dest to the * box the PAP2 has both lines registered @ ports 5060 and 5061 and work like a charm. one of the

Hi all, I'm trying to provision my PAP2T's to use a SVR lookup to find the Asterisk server. I'm using a provisioning file that contains an element like: <Proxy_1_> _sip._udp.example.com </Proxy_1_> However, the PAP doesn't seem to be able to find my server with this hostname. The DNS records are in place because my Polycom and Grandstream servers work just fine.

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Help? ntfy-mailto.c: In function ?ntfy_mailto_send?: ntfy-mailto.c:505:5: error: too few arguments to function ?smtp_address_create_from_msg_temp? sieve_get_postmaster(senv)); ^ In file included from ./../../../sieve-types.h:5:0, from ./../../../sieve-common.h:7, from ntfy-mailto.c:30: /usr/local/include/dovecot/smtp-address.h:101:5: note: