similar to: Description of Zaptel/DAHDI E1 alarms

We are having line noise issues in our Asterisk to legacy PBX integration. All SIP calls originating from IP phones sound crystal clear. All calls that originate from the legacy PBX (Isoetec 228) and route through the Asterisk and out SIP have a lot of line noise. I believe I have it pinned down to these Blue Alarm errors that I can see on the legacy PBX side. zttool shows no alarm but when I

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

I'm using a Te201p card, with unichan, I want to know if my channels are "ready" or in alarm... but uc show channel o uc show channels, doesn't show me anything... Any Ideas? thanks.

I have 7965 and am trying to convert the firmware to SIP (SIP45.8-3-4SR1S). Does anyone have a valid XMLDefault.cnf.xml they could share? I have tried the version at voip-info<info.org/wiki/view/Asterisk+phone+cisco+79x1+xml+configuration+files+for+SIP&view_comment_id=14768#Troubleshooting>for the 7941/7961 but unfortunately /var/log/messages shows in.tftp stops sending after

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

Hello I have contacted my line provider who is saying that in order to get my 0845 or 0870 number to id as the incoming number on a landline that i may call i need the following. User must provide - NPI set to E.163/E.164 User must provide - TON = "national or international I have had a good search around and can't seem to find a good answer to this. Does anyone have any idea where i

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hi All; Suddenly the zaptel channel look like stop working and it is giving me this error when I do zap restart: [May 24 19:30:21] ERROR[2772]: chan_zap.c:7219 mkintf: Unable to open channel 1: Device or resource busy here = 0, tmp->channel = 1, channel = 1 [May 24 19:30:21] ERROR[2772]: chan_zap.c:10582 build_channels: Unable to register channel '1,2' To what it could be related?

Folks, I really hope you can help me here - I'm beginning to tear my hair out! About 10 days ago my company moved to a new office. As a result of this, we've plugged our PBX box, which has happily been running for the last three years, into our new E1 line. Since then, I've been seeing intermittent yellow alarms. Obviously, since this was working fine in the old office, the thing to

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

I've got a nagios plugin making sure the * box is up, but I would like to do more than that. I need to make sure the PRIs connected to my box stay up and I need to make sure calls are not failing for any reason. Are there any * monitoring packages like this? -Daniel

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040810/16371a21/attachment.htm -------------- next part -------------- ? Hi, I'm using TE410P card with four T1 lines. I've configured all the channels in my /etc/zaptel.conf file. In zttool i'm getting "OK" for the "Span-1" but the other three spans giving

Hi All, I have installed newt and newt_devel but dahdi_tool will not compile/install. I'm trying this with dahdi-linux-complete-2.5.0.2+2.5.0.2. does anyone have any suggestions as to what I am doing wrong? Regards David. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anyone succesfully used TDMoE on Fedora Core 2.6.12+ Kernel versions? I'm having the issue that is in the Mantis bug database with badness with the kernel. My Story: I can get the dynamic span to come up and show OK in the zttool on both machines. However i get errors every second (Warning: detected alarm on channel 1... then channel 2...) And then the next second, i get : alarm

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco