similar to: CDR Rewrite -- Questions to the users (Steve Murphy)

Quoth: OCG Technical Support <support at ocg.ca> > >Although we've programmed the softkeys per the manuals, they seem to have no >effect (just dead). For example, our 57i is setup like this: I had similar problems and ended up using the speeddial inband functionality. FWIW, my 57i's setup like so: softkey4 type: speeddial softkey4 label: "*Park" softkey4

I'm trying to keep the DND status of my Snom phones and the astdb in line but I'm stuck on integrating my gui DND button which talks to * using the manager interface (actually it uses Astmanproxy as the gui host is on a different network to asterisk and can't see the Snom's across the network). All's working fine in my Dialplan; when someone dials the code for DND-on or

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

I've just started deploying these (well the T28P model) after years of Snom issues and they look pretty good (although the documentation is execrable; if you thought the Snom stuff was obtuse Yealink have got them knocked into a cocked hat!). Anyway, for provisioning I use HTTP with a DHCP entry like:- # # Yealink Phones # group { #

I have two Asterisk systems that can route to each other via a VPN with firewalls disabled for testing purposes. Each Server can see (tested via nmap) UDP port 5060 on the other. So... I thought that I could simply use a Dial command in Server A's config to place a SIP call to Server B... but it doesn't seem to work. Server A (192.168.1.33) has: exten => *136,1,Dial(SIP/90 at

Is there a SIP header I can set (for Snom and Yealink phones if that's relevant) or any other mechanism to tell a phone to ignore a particular call from it's missed call list? I have bits of the dialplan that ring groups of phones eg: exten => 200,1,Dial(Sip/112&SIP/113&SIP/114) and I don't want such calls being recorded by the phone as a missed call. Calls to the

I'd like to be able to generate a Manager Event from the dialplan but can't seem to find a way to do it. Alternatively, trigger and Event when a record in AstDB gets changed. Can anyone point me in the right direction? Thanks. By way of explanation, I've a app that connects to astmanproxy and I'd like it to know when a call group gets put into Nightservice. Putting the call

cdr_mysql doesn't set the userfield when it's set inside a macro called from a feature (1.4.25, addons 1.4.8). I have a feature code: autorecord => *1,self,Macro,apprecord The apprecord macro looks like: [macro-apprecord] exten => s,1,Playback(beep) exten =>

Does anyone have any suggestions for a decent receptionists phone? Aastra? Grandstream? Something with (potentially) lots of BLFs, large(ish) screen, headset and most importantly the ability to transfer calls? I've installed five Snom 370s that seemed ideal but my client is very very unhappy as the Snom 370 can't transfer a call correctly if there's another call coming in (details

Don't you just hate it when something was working and when you come to use it in anger it's broken :-( Something in the, fairly, recent series of Asterisk updates has broken DIGITAL call passthrough. I've an ISDN PBX behind my Asterisk Box (PRI ISDN comes into port 1 of a Digium Wildcard and the PBX it connected to port 2 via an ISDN crossover cable). This PBX used to be able to

Hello Happy New Year to all!! I've just completed porting from Asterisk 1.2 to 1.4. I did this by doing a clean install on a new box, and moving over configuration and scripts where needed. All went surprisingly well! Anyway, one lingering issue is that the function key "lamps" on our Snom phones have all stopped working! We're using a mix of Snom 290/320/360 phones and

Can anyone help with the use of regexten? (* 1.4.3) I've got Asterisk creating extensions for my SIP phones using regexten but I can't seem to figure out how to make use of them once they're registered. Here's my dialplan for from-sip (the SIP's default context): asterisk*CLI> dialplan show from-sip [ Context 'from-sip' created by 'pbx_config' ]

This is concerning an Asterisk 1.4.18 server. We have approximately 70 DID numbers. Incoming calls are placed into the "incoming" context (by zapata.conf) and are routed based on the dialed number. I want to do some manipulation (CallerID name override) to all incoming calls before they are routed. I would prefer to avoid duplicating the necessary code in each DID extension stanza,

Hi All, Has anyone hooked up * as an extension/trunk of an Avaya system that has around 2 ISDN30e's. Trying to add 100 extensions to one of our systems, but not sure where to start reading. Thanks. -- Kind Regards, Gavin Henry.

I'm seeing both inbound and outgoing call failures on our ISDN-30 lines that only seem to go away when I do a "zap restart" or in extremis restart Asterisk (1.4.25 with a Digium TE205P and zaptel 1.4.12.1). If I don't restart zapata or Asterisk the problem rapidly get worse :-( The lines are from BT with LCR from Cable&Wireless (I've tried using the LCR bypass code and

Hi All, I'd appreciate some help on how to implement "call stealing". That is, where you dial a code to redirect any call on the system to your handset. I'm getting rid of my BRI service and I'm trying to replace the functionality of my existing ISDN2e PBX (Cybergear Gold) with VOIP and Asterisk. On my ISDN PBX, the short-code *46 does this. For example, if I take a call on

Asterisk seems to be ignoring DTMF for features in Asterisk 1.4.0b3 My SNOM sends the dtmf-relay and Asterisk gets it because I can see it in the sip debug. However, once seen, Asterisk doesn't actually do anything about it. I've checked features and that seems fine. Is this a bug or something that I've screwed up? For the record, here's the features setting: asterisk*CLI>

Once in a while, someone mis-dials when transfering a call on their Snom SIP phone (using the Transfer button). Instead of sending them to, say, 1940; they mistype and enter 194 or 190 or somesuch. This ends up on the PSTN (for which three digit calls are valid); not what anyone wanted. On our old PBX (Network Alchemy Argent Office) there was a dialcode that grabbed back the last call that went

I'd like to be able to playback a file to *both* channels in a call as a result of a DTMF feature. Can anyone suggest how I might do this? I thought of using a DYNAMIC_FEATURE to call a macro that starts a dynamic meetme.... but the macro only gets to control the 'caller' or 'callee' :-( Failing that.... I'm trying to provide a simple means of playing back a recorded

I'm tearing (what's left of) my hair out on this one :-( <shortform> How can I set the CDR(userfield) in the calling thread from the dialplan (actually a macro called from a feature) in the called thread? <long version> I use mixmonitor to record calls driven by entries in the asterisk database for selected phones. As part of this dialplan, I set the CDR(userfield) to the