similar to: Check variables on a live system - Is it possible?

Hi, I'm using a Junghanns Quadbri ISDN card on some lines from the Austrian Telekom. Things are working, the only missing stuff is to add a "0" as a prefix to each incoming call, to make it possible to answer missed call lists. I'm using the 0 as the prefix for outside lines. I've experimented a little with the prefix settings in zapata.conf, but without success:

Dear All, Thank you for taking the time to read this post - I am *confused!* as to why my asterisk setup does not work as it should. I have an ISDN 30 connection for telephony, a Sangoma card, and asterisk installed. Incoming calls, and outgoing calls work 100%. Making an international call, results in silence, or the error message all circuits are busy Numbers being passed to the trunk for

This is, hopefully, just a case of brain fade. With zapata.conf and zaptel.conf in place, asterisk loaded, no dial plan and all LEDS on the card lit, I get no dial tone, plugging an analog phone into ports 1 or 2, only a buzz and click. zaptel.conf - defaultzone=us loadzone=us fxoks=1,2 fxsks=3,4 zapata.conf [channels] signalling=fxo_ks language=us context=phones-1 group=0

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

Hi, I've an PRI coming to my asterisk ,calls are coming fine and my agents are able to answer no prob. but I've an agreement with my telco with some incoming no if the no of calls on these no are more then 3 then send to another no. they use busy signal to divert call on another number so I'm sending the call to Congestion() if no of calls in this group are more then 3. But my

getting some errors on my test system. this is 1.4 (Asterisk SVN-branch-1.4-r214194) with a 4 port T412p card. Three of the ports are connected: Span 1 to the PSTN on a 10 channel bearer line, ports 2 and 3 are cross-overed (!) to each other. Port 4 is not plugged in. This has been working fine for several months. I updated a few days ago to the latest 1.4 branch. However, now I cannot dial into

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hello I have upgraded our asterisk box from zaptel to dhadi two weeks ago... Since, there has been quite a significant amount of echo when making a call. Only for the local outgoing call, the person on the other side doesn't hear any echo. This is with a TE-110P ISDN PRI card .. I've pretty much took the original zaptel configuration and used it as-is with the dahdi one ; to no

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

I'm trying to upgrade from 1.4.24.1 to 1.6.0.9 with a TE120P card. I can't make any connection over the T1. From CLI: ERROR[26017]: chan_dahdi.c:14300 process_dahdi: Unknown signalling method 'pri_cpe' at line 37. cat chan_dahdi.conf cat chan_dahdi.conf [trunkgroups] [channels] language=en ;internationalprefix = 00 ;nationalprefix = 0 context=from-pstn switchtype=national

Hello, I was testing my asterisk for a while with 1.6 without much problem. Now i am trying to install a new system with asterisk 1.4 but now i am using a dual pri card instead of single pri.(TE220P) What i want is to use both PRI ports as group. Now i have zaptel.conf file created as follows -------------------------zaptel.conf-------------------------- # Span 1: TE2/0/1 "T2XXP (PCI)

Hi, I've always used dahdi-genconf to just create the dahdi-channels.conf and since our PRI is fairly simple (just dump all the channels into one group) it works with dialing with dahdi/g1/(number). I'm trying to understand the file though for my own reference. It seems the file looks like this: group=0,11 context=from-pstn switchtype = national signalling = pri_cpe channel => 1-23

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi list, After upgrading from Asterisk v1.2 to v1.4.14, all kinds Zaptel error messages related to my HFC-S PCI card disappeared, but now I can't access the card's resources because it always seems to be busy. Any idea why? Thanks, Jaap PS -- Below is some info regarding my configuration. =========================== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian