similar to: [SPAM] - Dahdi, b410p and looping from 1 port to another - Email found in subject

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Apart from you were dialling out on your inbound context and vice-versa. The best advice I can give now is to change to mISDN - as this is proven to work with v1.4 and v1.6. Actually - have you tried putting the 100ohm termination on for your NT port? I need to do that with mISDN as it only allows ptmp for ISDN extensions. Cheers Andy -------------- next part

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hi, At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point to multi-point mode. Here (France), most small PBXes are connected to ISDN through BRI trunks in PtmP (don't know why but it seems the general case). So this NT-PtmP function would be very helpful to easily slide an Asterisk box between an existing PBX and the network. Does the same case apply elsewhere (UK,

asterisk-users at lists.digium.com has now been added to the filters white list! Anyway, 100ohm termination isn't required for ptp - but is required for ptmp. I know the DAHDI package(s) no longer include make b410p - hence the reason it is included in the docs.

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hello, Junghanns and BeroNet offer 8 BRI ports cards. Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out of 2 B410P ? I know you could (theorically) do this with Junghanns and BeroNet cards. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

We have an Ubuntu Dapper with 2.6.14 kernel, asterisk 1.2.14 debs from http://pkg-voip.buildserver.net When misdn stuff (misdn-init start) is not started, everything is fine, our 8 FXO (Channel 1-8) 4 FXS (21-24) are working well. If we start the misdn stuff (one card, port 1,2,3,4 in misdn-init.conf and no TELCO cable plugged in the card), the dialtone disappear on TDM lines :-( Does

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Hi all, I wanted to switch from my current setup (mISDN) to the native dahdi with b410p support (wcb4xp). All works fine for normal phone calls but not for faxing. Faxes are distorted, if arriving at all, and hylafax logs the usual bad stuff (HDLC frame not byte-oriented.) Our setup uses a digium b410p card with asterisk 1.6, latest libpri and dahdi, hylafax with iaxmodem, and all this on 1

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden