similar to: test OpenVox B400P and junghans card for dahdi BRI wcb4xxp

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Dear all, I know this is more a Digium hardware than an Asterisk issue. Already posted a question at Digium, however also like to see whether anyone in the Asterisk community has encountered the following situation: I installed a Digium B410P BRI PCI card on my new asterisk server, following the steps specified in the manual. I can see the PCI card is available using the lspci command: ...

Hi, a few month ago, I tried to install zaptel for my Beronet BN8S0 pci card... I gave up and took hfcmulti/lcr. Now dahdi (2.2.1.1) seems to support the card and I'm very interested to get it to work. But how to get rid of these annoying qozap driver? bishop dahdi # lspci -v -nn -s 01:00.0 01:00.0 ISDN controller [0204]: Cologne Chip Designs GmbH ISDN network Controller [HFC-8S]

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hello, ? I have a Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] card which seems to work on 1 machine but not on another. It SHOULD load this driver: ? >dahdi_hardware -v pci:0000:00:00.0 wcb4xxp+ 1397:08b4 Junghanns QuadBRI ISDN card Instead of: >dahdi_hardware -v pci:0000:00:00.0 qozap- 1397:08b4 Generic Cologne ISDN card There is no qozap modul in

Hello, In my system, dmesg outputs : [ 13.039788] wcb4xxp 0000:01:0a.0: probe called for b4xx... [ 13.039788] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 13.039788] wcb4xxp 0000:01:0a.0: Identified HFC-8S Junghanns.NET octoBRI PCI (controller rev 1) at 0001dfe0, IRQ 21 [ 13.041202] wcb4xxp 0000:01:0a.0: NOTE: hardware echo cancellation has been disabled [

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi, I'm using Asterisk 1.6.1.18 with latest Dahdi Linux and Tools (rev 8854) and libpri 1.4.10.2. During installation, I'm facing this : # dahdi_genconf -v system Default parameters from /etc/dahdi/genconf_parameters Empty configuration -- no spans Of course, I've got span descriptions in /etc/dahdi/genconf_parameters : .... pri_termtype SPAN/1 TE SPAN/2

I did an svn check out of dahdi. I am running centos 4.7 on the make all I get an error. /usr/src/dahdi-complete/linux/drivers/dahdi/wcb4xxp/Makefile: No such file or directory make[4]: *** No rule to make target `/usr/src/dahdi-complete/linux/drivers/dahdi/wcb4xxp/Makefile'. Stop. make[3]: *** [/usr/src/dahdi-complete/linux/drivers/dahdi/wcb4xxp] Error 2 make[2]: ***

Hi, On my system I've got : CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO B4XXP (PCI) Card 0 Span 1 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI) Card 0 Span 2 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI)

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When