similar to: ISDN Cause Code 100, Bosch Integral Management Connection

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

When I restart or reboot I can not dial out. The dial() incorrectly sees dahdi/1 as busy. I call in once from a cell phone, which is successful then I can call out with out issue. Any ideas would be much appreciated. Sangoma B600de asterisk-1.6.0.9 dahdi-linux-2.1.0.4 linux-2.6.28-gentoo-r5 wanpipe-3.3.16 ###chan_dahdi.conf ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:

I have been trying to sort this out for a while now but with no luck I have isdn <-> asterisk<-> pabx on a te205 incoming calls work fine outgoing calls seem to work fine but the call is dropped when answered I think it is to do with the line [May 8 17:51:55] WARNING[4762] channel.c: Unexpected control subclass '5' that is causing the problem but I don't know how to

Well, I thought I had my problem solved, but it is acting up again. Hopefully this time I can provide enough information. What I have is an * box setup with one X100P and TDM400 with one FXO and one FXS. For my regular setup with interfacing with my PSTN and my entire house with analog phones, the box is working great. I am trying to interface a Mediatrix 1202 device to my * box via the

I'm seeing both inbound and outgoing call failures on our ISDN-30 lines that only seem to go away when I do a "zap restart" or in extremis restart Asterisk (1.4.25 with a Digium TE205P and zaptel 1.4.12.1). If I don't restart zapata or Asterisk the problem rapidly get worse :-( The lines are from BT with LCR from Cable&Wireless (I've tried using the LCR bypass code and

Hi, I've set up an Asterisk as voip gatway: VOIP <-> Asterisk <-> hfc-s card <-> NTBA <-> Siemens Gigaset Dect ISDN pbx. Outgoing calls from dect handset to the world are working. Incoming calls don't even ring the handset. I'm using the dahdi driver with the zaphfc kernel module. The hfc-s card is in nt mode. The msn is set at the dect phone/base station

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

And I'll resend this one too. Silly scalix. --Rob -----Original Message----- From: Rob Thomas Sent: Thursday, 22 June 2006 12:19 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] zapata.conf: recent changes? Looks like you've stopped compiling libpri. All those options that are being ignored, are being ignored because they're

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

Hi! I am trying to setup a simple queue in Asterisk and I'm having a small problem. Our callers come in through a Bosch PBX and are immediately transferred to an Asterisk menu/IVR. If they select the option to call a SIP phone directly (eg. entering the operator's SIP extension) then the callee/operator can transfer the call to a phone within the Bosch system. What Asterisk does is

Hi All, Twice now in the past few weeks I've walked into the office to find that our 1.2.24 Asterisk process is sat at 100%, and that hundreds of thousands of log files in /var/log/asterisk exist, all at 312 bytes, containing: Aug 29 23:22:17 VERBOSE[24303] logger.c: Asterisk Event Logger restarted Aug 29 23:22:17 VERBOSE[24303] logger.c: Asterisk Queue Logger restarted Aug 29 23:22:17

My international calls are not connecting. [general] pridialplan=dynamic ;prilocaldialplan=unknown internationalprefix=00 nationalprefix=0 localprefix= I have the above in my zapta.conf - yet when I dial an international number, I get a ring, then I get the message "the person you are calling, is currently unavailable" This is an ubuntu machine, with a sangoma card, with

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

Hi! I want to test Asterisk<-->Siemens HiCom integration using Q.SIG instead of ISDN. I did not find any documentation about Asterisk und Q.SIG. Thus, I wonder is it sufficient to set "switchtype" from "euroisdn" to "qsig" or are there any other things which I have to take care of? Thanks Klaus

Signed-off-by: Arthur Clement <aclement at linagora.com> --- src/host-browser/host-register.rb | 16 ++++++++++++---- 1 files changed, 12 insertions(+), 4 deletions(-) diff --git a/src/host-browser/host-register.rb b/src/host-browser/host-register.rb index 693a6f2..5ff6a90 100755 --- a/src/host-browser/host-register.rb +++ b/src/host-browser/host-register.rb @@ -393,13 +393,18 @@ class

hi. could somebody explain how exactly the following parameters in zapata.conf work: pridialplan prilocaldialplan internationalprefix nationalprefix localprefix privateprefix unknownprefix the wiki & comments doesn't quite explain them. and phone companies are absolutely no help. i've setup systems in the US & China with trial & error until it works. now i'm setting up a