similar to: Zaptel FXO offhook when connected to PSTN

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Happens quite often. X100P FXO card puts the PSTN line offhook, so that no calls go out or come in. The outside callers get a busy siganl while inside callers cant dial PSTN. Its a DELL optiplex P3 128MB ram 500MHz processor. Here is some more info: (see the zapata.conf in the end) Please direct me where to look for problem. Thanks!!! ======================================== pbx1*CLI> zap

I am unable to dial out over a Wildcard TDM400P. This was working previously, so must have messed up the config somehow. I'm running Asterisk 1.6.0.15, with FreePBX 2.5.2.2. When I dial, I see: -- Executing [s at macro-dialout-trunk:19] Dial("DAHDI/1-1", "DAHDI/g0/9239220,300,") in new stack == Everyone is busy/congested at this time (1:0/1/0) It looks like the

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

OK... so I'm not sure what I'm looking at. I've had the good old echo problems on my Rev C FXO again this morning, so I thought I'd attempt some debugging, though I'm not sure what I'm looking at. This call has echo. Channel: 2 File Descriptor: 20 Span: 1I> Extension: Dialing: no Context: incoming Caller ID string: "External Call" <99999999> Destroy:

Hi, We are having a problem with asterisk detecting that an analog ext has been put down. This seems only to happen after a number of calls have been made. We have an FXO port (TDM400P with FXO module) connected to our PBX and are using this to test asterisk prior to rolling our for our small office. What happens is that we make a number of calls to this ext which 1st rings a phone (FXS)

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.

My office is investigating using an Asterisk PBX and also going to a VOIP provider for our main phone connections, but one of the tricky things is that we need to have outbound and inbound modem calls (fax too). I see a lot of talk about faxes but no mention of modems on this list. I get the impression that modems will be a problem for us. Is that true?

Hi, I'm trying to make a dialup internet connection through my asterisk PBX. When I bipass the Asterisk box, I can get 51600bps. When I run through the asterisk box, I'm limited to about 21600bps. I have a TDM31B card. Any help on speeding these connections up would be good - I was on the understanding that if you bridged the channels, then the call should essentially flow straight

Hi, We've got a dedicated T1 with two trunks running into our ILECs selective router for 911. Split out of the T1 into two MF CAMA trunks on ILEC side. I'm trying to use asterisks e911 signaling, but I'm having trouble with the dial command. (== Everyone is busy/congested at this time (1:1/0/0)) I'm missing something and I'm thinking it has to do with the hookstate

Hello all, I have an asterisk box running in a customer with Hylafax, iaxmodem, asterisk 1.2.18. The service can receive faxes, from a lot of fax machines, but there are a couple of them that asterisk Hylafax cannot complete. This calls arrive the asterisk box, asterisk detect that this calls are fax, asterisk answer the call, and then Hangup the call. But hylafax do not receive nothing. When

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body bgcolor="#ffffff" text="#000000"> I recently upgraded my Asterisk system to Dahdi and now I have an echo problem.<br> <br> I am running Asterisk 1.4.25 with Dahdi Complete 2.2.0, on a Digium TE121B PCI express card with a HARDWARE echo

The problem: T100P connected to an Adit600. Channel 1-16 are FXS, 17-24 FXO. I have Zap/24 in callgroup 3 and Zap/1-16 in pickupgroup 3. When a call comes in on Zap/24 I cannot pick it up with *8 from Zap/1-16. *CLI> show version Asterisk CVS-04/27/04-23:48:08 built by root@tuck on a i686 running Linux The zapata.conf and extensions.conf are located here:

In order solve my incoming caller ID problem, I upgrade the dahdi to version 2.6.1 from version 2.4.x. After upgrade, I found the echo cancellation doesn't working (I'm using Digium AEX800B PCI Express card). I can hear my self talking on the phone. How to solve this? I think I need to recompile dahdi 2.6.1 with OSLEC support? how? [root at callcenter ~]# dahdi_cfg -vvv DAHDI Tools

Hi guys, This has been bugging me for days and I can't figure out what's happening. Using the same channel on DAHDI, I can't make a call after previous one being hung up by remote side. However, it works like it should if my end hangs up the call. To make things interesting, DAHDI, or astribank rather, seems to "reset" itself after receiving an incoming call on that DAHDI

I have a TDM400P with fxo and fxs modules, and local extension calls work fine but I can not dial-out. I am getting both problems on FreeBSD and Linux, and plugging a regular telefon set works fine. Any ideas of what I am missing? thanks micko Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default)

Hi I have the X100P card which as to sockets (LINE - for fxo line ) and PHONE (to connect a n analog line) This card is setup as fxs_ks I was getting dial tone but suddenly no Dial Tone....Help appreciated.... When I try to route the Call using - Dial Zap/1) to this FXO Line I get this error: ------------------------------------- linux*CLI> -- Executing

Hello, I have a strange problem with one of my Zap channels. A user told me that he was in a voicemail system during a call, hit the Flash button, and the call hung up. Now we get no dialtone on the phone hooked up to the channel. Here's the status of the channel: jmartin at rogue:~$ sudo asterisk -r -x "zap show channel 7" Parsing /etc/asterisk/extconfig.conf Channel: 7 File