similar to: AGI defunct processes + GSM Playback - HELP!

Howdy, Just installed a new switch in a new location (Ubuntu, 2.6.24-24 kernel, zaptel 1.4.12.1 built from source, libpri-1.4.10.1 built from source, asterisk 1.4.26 built from source, wanpipe 3.5.4 built from source, Sangoma A104d with firmware that is probably a year old). I plugged in an RBS T1, ESF, B8ZS, wink start, and MF signalling. I stuck with the defaults that the wanpipe build

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all went okay. using sangoma a104dx on both machine. I followed the write up on http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 =

My Sangoma Experience in Asterisk: Followup 2005-05-06 original review can be found at: http://astguiclient.sourceforge.net/Sangoma_experience.txt It's now been a month since I finished my last round of tests with the Sangoma A104u board in Asterisk. I have had a lot of conversations with the guys at Sangoma about how my system runs so that they could set up their test systems to try to

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Hi all, I am having a very strange problem. I am terminating a PRI (5ESS switch type, national plan, 23B+1D (24)) into a Sangoma A104 and am not able to produce any audio heard on the PSTN end of the call. Not sure what's wrong - the card worked before under a Trixbox setup. I'm running kernel 2.6.19 (tried 2.6.24.3 but had to downgrade as wanpipe stuff would not compile), zaptel

hi, i'm added another patch to chan_ss7 it's from Denis Smirnov http://download.seiros.ru/SeirosPBX/chan_ss7/ New in version 0.10.1 (community version) - support for more than 256 channels - zap style addressing http://download.seiros.ru/SeirosPBX/chan_ss7/ http://www.freevoice.cz/chan_ss7/chan_ss7-0.10.1.tar.gz md5sum a3ca3031f8f4ef96d505be3b297b47cc

Hello, I've installed Asterisk and Asterisk GUI 2.0. The GUI says "No Analog Card found" and /etc/asterisk/ztscan.conf is empty. I see the following message from asterisk, <snip> -- Executing [executecommand at asterisk_guitools:1] System("Local/executecommand at asterisk_guitools-a145,2", "uptime >

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

hello, all of users: sorry, resend it again for clarifying the message. I have implemented cha_ss7 in china. initially, the chan_ss7 can not support the call group. i modify the code. now the problem is that, both sides can hear the ring, but i can not hear the voice from each other. i think the ss7 does not send the voice steam to the destination. in chan_ss7, i added:

Hello everyone, I am trying to apply this<http://www.voip-info.org/storage/users/496/27496/images/499/rbt.patch.diff>patch on chan_ss7-2.1.0 for RingBack tone but its not accepting and throwing errors: Hunk #1 FAILED at 704. Hunk #2 FAILED at 715. I have done the patch modifications manually in l4isup.c There is just one question, how do I pass the RB file-to-play on an SS7 channel via

Hi all ! We currently have an asterisk box that is rather old (runs Asterisk 1.4.21.2), and it's connected to the PSTN with a sangoma A104d card. Now we have a new PRI at another location, and I use that occasion to build 2 new servers, one to replace our aging one and a new one for this new pri. So I downloaded the lastest libpri / asterisk / wanpipe driver, but the previous version of

Hello, Have you tried the wanpipe-beta8c-2.3.3.tgz release in the custom/2.3.3 dir on their FTP site? Also, have you contacted Sangoma for support? They are very responsive. I am using wanpipe-beta8a-2.3.3.tgz and it's been working great on my A104 for a week now. MATT--- -----Original Message----- From: Dmitry Zhukovski [mailto:DZH@comx.dk] Sent: Monday, May 09, 2005 5:20 AM To: Asterisk

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hi again, Well - I didn't see beta8a-2.3.3 in custom dir. Will try. Also I tried to contact Sangoma - they are very fast to answer but main problem is time difference - it's 6 hours between Canada and Europe. Br, dmitry Dmitry Zhukovski System developer ComX Networks A/S Naverland 31, 2 DK-2600 Glostrup Denmark Phone: +45 70 25 74 74 Fax:???? +45 70 25 73 74 Web: www.comx.dk

Hello everyone, since some weeks I experience strange problems on my gateways to the PSTN. The gateways use chan_ss7 and SIP. My setup is roughly like that SER --> Asterisk A --> Asterisk B (chan_ss7) --> PSTN What happens is, that after a while (uptime was a least two days) the gateway starts to not transmit audio to the PSTN on outgoing calls, but the caller can still hear the called

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hello, Several people asked to get a hold of the stats I used to determine that the Sangoma T1/E1 boards performed better in our real-world tests than the Digium boards. We've decided to post our results after confirming them over the past month of operations. Here is a link to the last two reviews I wrote about Sangoma with Asterisk:

samba-tool dbcheck --cross-ncs --fix Yes, should be possible, but i normaly do that after i do the following. search for : CN=58eba604-07e5-4c5d-a104-9e6f4907248f And CN=16b8c008-6c59-4b65-9f1b-530751904a75 In _msdc.dom.tld. Verify which GUID is removed, you can see that, then remove the old server GUID. Run : dig CNAME 58eba604-07e5-4c5d-a104-9e6f4907248f._msdcs.ad.fvg.lnf.it dig CNAME