similar to: DTMF detection problem on DISA

Hi everybody, Is there any way to remove dialtone from DISA? If yes, how to do it? -- Zeeshan A Zakaria -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080917/e7e17a0d/attachment.htm

Hello, I noticed that changes to realtime sip peers are not applied until a 'reload'. A 'sip reload' does not make any changes to realtime sip peers. When changing for instance the mailbox-parameter in the realtime sip_buddies table, the change is not applied with a 'sip reload'. For every change there is a complete 'reload' necessary. Why does a 'sip

Hi, I am having this issue that with one of the Asterisk servers, on zaptel hardware, that DTMF tones are 10-30 Hz too high than the upper limit for any DTMF digit frequency. This is causing problem with the equipment on the other end which is trying to recognize the DTMF digits. I tried different cards from the same vendor but it didn't help. For example for digit 1 where it should generate

Hi Folks, I'm trying to test out Asterisk overall. I'm having some problems with DTMF. Currently I'm playing with DISA, but I'm worried this will happen when I get to implementing AAs etc. I have a free SIP trunk from IPKall that I'm trying to make work. I'm able to receive calls, and I've now setup and extension with DISA and a password. I connect ok from the

I can dial from an asterisk host to another one via FreeWorldDialup, on the other side DISA service answer to me and i can ear dialtone. But i cannot send DTMF and dial an extension on the DISA enabled asterisk.....i've tried rfc2833 and inband...but nothing....any tips ??? Thanks, -- Igor Barsanti GPG Public key available at http://pgp.mit.edu

[This email is either empty or too large to be displayed at this time]

Hi, In last one week I have seen two servers of our organization successfully hacked and some other under attack from some other IP addresses. We would block one IP address on our firewall and after a few hours, they would start getting hits from some another IP address. When I checked them on whois.net, they all were from Amsterdam. Surprisingly, I once had similar attack in the past and it was

Hi, After some testing I've found out that my client's hardware recognizes DTMF only if digits are sent 50ms apart with 50ms of tone duration. This was tested using a test device which generates DTMF. Now asterisk doesn't do it by default because digits going out from Asterisk are not being recognized. Using command sendDTMF, I can control inter-digit duration, and using

Is there any known reason that the DISA() routine should behave differently than WaitExten() as far as recognizing DTMF tones? If not, I suspect there's a bug here. Try it yourself--two DID's on our PRI, numbers below let you test each routine: It is my observation that some setups/phones DO and some DO NOT express this variance. --I could not show any variance on a sprint mobile phone

-------------------------------------------------------------------------------------------- Originally posted at http://forums.digium.com/viewtopic.php?t=18045 -------------------------------------------------------------------------------------------- Hi! I'm trying to configure a DISA setup (Asterisk 1.4.11). Only, executing DISA seems to prevent any DTMF detection capability when using

Hi, I am using zap channels, and by using sendDTFM application, I can control the duration between two DTMF digits, but I can't find a way to control the duration of the digits themself. Did search on the Internet and found out that I can change it in the asterisk source files and recompile asterisk. Wiki also says that it can be controlled using toneduration option in zapata.conf, but it

Hey, this is happening to anyone who I try this with. We get into the DISA, then hear the dial tone. Dial 1 then start dialing the number, and it hangs up. I thought adding a wait time after the DISA may help, I was wrong. Here is what I have thus far in the DISA extentions. [DISA] exten => 7,1,DISA(no-password||"Scheda" <565> 455-1337) exten => 7,2,Wait(45) exten =>

Hi, These days I run into something quite odd. I have an A@H that was modified to meet our requirements. We have a completely funtional DISA which we use pretty much all the time. I works flawlessly with incomming SIP calls from several providers, IAX calls from FWD and with ZAP. Recently we came out with a situation where it doesn't work... with a

Hi, I'm getting unusable DTMF detection with DISA on incoming ZAP channel (bristuffed *) on quadbri from GSM gateway. DTMF detection works ok in normal ISDN incoming line. How can I check what's going on ? What settings to check ? Anyone with more experience on such scenarios ? Thanks in advance, regards, Rob.

Hi list, I am planning a migration to virtual machines, and was considering with it to move from 1.4 to one of the later versions. My and my clients' 1.4 setups have been rock solid and I don't want to put myself into any unnecessary trouble. Those of you with solid experience with all these versions, what would you suggest? What new and exciting enhancements would newer versions bring

Hi, I have just setup a DISA setup whereby people can dial in, authenticate, are given a dialtone and can then call out. Everything works however there is a 10 second delay after the user enters the number and presses #, until the system does anything. Here is the relevant section from my extensions.conf: -------------- next part -------------- An HTML attachment was scrubbed... URL:

We are using DISA with local SIP users. The user enters in a 2 digit code then they get a dialtone and the phone dials out. The problem is that the calls waits 10 seconds after the outgoing number is dialed, no matter what I put for the timeout values. Anyone else using DISA that has run into this? exten => _2X,1,Answer exten => _2X,2,DigitTimeout(2) exten =>

Hi, I'd set the daylight saving option to yes on all the GXP-2000 phones, but apparantly it doesn't move it an hour back on last sunday of October. So now I am stuck will all the phones showing the wrong time. Isn't there an option so that it'll automatically update daylight savings? Thanks -- Zeeshan A Zakaria -------------- next part -------------- An HTML attachment was

I've commited changes to Voicemail2: * Handle properly when being left a message while checking VM -- this should fix the "saving to your inbox" issue too, at least in principle. And to DISA: * Properly handle extensions with multiple matches and "dots" Please let me know on or off list about any feedback you have regarding these changes. Mark

Hello list, What servers would you suggest for:100 concurrent SIP calls, 4xT1 card, and a not much busy website, i.e. getting 500-1000 hits a day. Thanks, Zeeshan A Zakaria -- www.ilovetovoip.com -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20101020/8ab7ae3e/attachment.htm