similar to: different gains per channel?

Hi everyone, Sometimes i am having problems with Zap channels on asterisk 1.2 (Disc-OS 1.1), after some calls, the channel continues in use, even after hanging the call up, then i need to run the "soft hangup Zap/<zapchannel>" in the asterisk CLI to release the channel. Here is my zapata.conf: [trunkgroups] [channels] language=pt_BR context=default usecallerid=yes

Hello! I'm having an echo problem with a TDM card. The TDM card is being fed by a channel bank just 12 or so feet away. When you put an analog handset on the line, both the RX and TX volume seem to be just fine. However, when I use the TDM card, I have to have an rxgain of 13.5, and even then, the audio is relatively quiet. I'm also getting echo on these lines, so I have turned

Hello, In my quest to figure out the source of the random echo on our shiny new asterisk install, I have been using ztmonitor on the TDM400p channels for the good part of today. I have 2 TDM400p cards with 8 FXO modules and 6 pots lines connected to them (last 2 channels are unused but configured in zaptel). Even when the lines are onhook, the Tx values settle down to 0 but the Rx values still

I am running Asterisk 1.2.14 and Zaptel 1.2.12 and using a Digium TE110P card in E1 mode. I've recently noticed in my logs the following Jan 5 01:27:11 VERBOSE[22490] logger.c: [chan_zap.so]Jan 5 01:27:11 VERBOSE[22490] logger.c: [chan_zap.so] => (Zapata Telephony w/PRI) Jan 5 01:27:11 VERBOSE[22490] logger.c: == Parsing '/etc/asterisk/zapata.conf': Jan 5 01:27:11

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

Hello, When I start Asterisk, I get the following in my log (/var/log/asterisk/full): Mar 15 17:16:55 VERBOSE[4242] logger.c: == Parsing '/etc/asterisk/zapata.conf': Mar 15 17:16:55 VERBOSE[4242] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Mar 15 17:16:55 DEBUG[4242] chan_zap.c: Failed to read gains: Invalid argument Mar 15 17:16:55 DEBUG[4242]

Good day list, I am feeling extra stupid this Monday morning and am hoping someone can come to the rescue. I am trying to use the ztmonitor utility on my wildfire 4 FXO card. and have read the following from the wiki. *********Wiki start******** If you set this to yes, use ztmonitor to adjust the rxgain and txgain. Ztmonitor isn't installed by default; but it is included with the Zaptel

Hi All, Channels 25-28 on a customers PBX are regular Zaptel FXO cards that are hooked into 4 incomming phone lines. They are all in a group to do automatic rollover for outgoing calls (if channel 25 is being used, dial on channel 26, etc.). Sometimes when a user is dialing a number, instead of bridging to one of the FXO cards it goes and rings to Zap/1-1. This doesnt occur all the time but some

Hi, I'm trying to find the differences between the two CLI gain parameters of Dahdi : "dahdi set swgain" and "dahdi set hwgain". When I change one of these parameters the output of : asterisk -rx "dahdi show channel X" | grep Gains don't show me any changes. Did "dahdi show channel X" shows HW or SW Gains ? Whan I set rxgain and txgain in my

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

I have a 12 channel PRI with SNOM 190's and asterisk CVS from January. Most calls are fine, all incoming calls are fine, but I am getting echo on a significant number of outgoing calls. The person on the other side hears a perfect call, but the SIPphone side gets to hear themselves. It happens 100% of the time to some numbers (outgoing only), and only sporadically to others. Has anyone

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

I'm using Asterisk 1.0.9, a Digium TE210P dual T1 card, and two Rhino channel banks (one 12FXO/12FXS, the other 24 FXS). So it's an analog phone on the inside connected to one of the FXS ports, and PSTN line connected to one of the FXO ports. My problem is that as soon as I hear the _first_ ring when I dial out through the PSTN line, I hear a tiny echo on the phone (I estimate between

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be

I've been going nuts lately trying to get rid of an annoying echo problem that makes my asterisk server unusable when clients try to call me. Here's the breakdown of the issue - Hoping that someone can throw me a clue: My setup is as such: Single AMD Athon machine with X100P clone card and voip through multiple providers . * Inbound calls through the X100P that do not bridge to

Hi there, we have a problem with dahdi and overlapdial. We are running an E1 in Germany and are in need of overlapdial. The E1 is connected to a Sangoma A101. As soon as overlapdial is set to "yes" we have problems with incoming audio on the dahdi channels. When set to "no" all audio is fine. Basically we can choose between being able to receive calls or to place calls

I'm having with an echo or delay I connect to the PSTN with a x100p and then connect a std. phone to a FXS module on a TDM10B. The std phone is only 2-wire so I know this is not helping. (yes I have read the 2-wire 4-wire issue) I have tried many echocancel values. The best thing to help was rxgain and txgain. below is my current zapata.conf file All help would be grateful. I have tried

I currently have Asterisk 1.2.7.1 and the Sangoma A200 w/ 6 FXO ports and HW Echo canceller. I have outgoing calling setup to use a group so that if one channel is busy it goes to one of the other channels. What's weird is that when I dial an outside number, sometimes it goes through and other times I get "You have reached an invalid pager number MCLL327." I have no idea what that

Hello, I have some problem to start asterisk. First I have followed a lot of tutorials to complete correctly the install process. Now it works when I type zttool I can see when I am or not connected to the PSTN. But, I run asterisk with vvvv verbose and I can't see the call detection. There is no detection of the call. I have a X100P card FXO with only one line. So only one channel I

I've spent all day today trying to fix an echo problem and I've made no ground whatsoever. I have Digium TDM400 with 3 FXO & 1 FXS. I've tried this computer at two completely different sites with different phone providers. I've tried compiling & installing different versions of Zaptel (currently running 1.4.0, started at 1.2.9 and worked my way up). I've tried