similar to: question about fxo cards

Hi guys, I think I posted on this issue before, but didn't get a response. I've still not been able to resolve the issue. I've got a small installation of Asterisk running one 4 port FXS Digium card and 1 FXO Digium card. I'm having difficulty routing modem call through one of the extensions out through the FXO card. By difficulty, I mean it won't work. The calls

Hi all, I am a huge fan of Sangoma cards after having many problems with digium cards and then switching to sangoma cards and them giving me excellent support with excellent results. That being said, they are also alot more money than the Rhino cards and my friend currently has 1 digium 4 fxo card in their system and they need to add another phone line, plus they have echo problems and quality

Thanks Rich, I have an SPA-3000 laying around, so I will attempt to set it up in a little more conventional manner (although your method looks like a winner for a home test PBX). Would you mind posting or PM your current config to me, maybe screenshots if you PM. If I start with that it will take less time to get to the point where the SPA-3000 is a true FXO-FXS gateway for *. I will be happy to

Message: 20 Date: Mon, 16 Jan 2006 00:18:18 +0000 From: Mike Hemstock <mike@csits.net> Subject: [Asterisk-Users] Choosing an FXO card To: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users@lists.digium.com> Message-ID: <200601160018.18517.mike@csits.net> Content-Type: text/plain; charset="iso-8859-1" Folks, I'm looking at buying an FXO card

Folks, I'm looking at buying an FXO card for my home Asterisk setup. The question I have is, should I got for a the Digium Wildcard FXO or settle for the winmodem that Digium sell? I have spoken to the UK distributor and they only sell the Wildcard. They said that the quality of the modem was questionable. Does anyone have any experience of this? Is the modem noticeably different

I get echo on my X100P for about 15 seconds then it disappears. Believe me, when I get a chance I'm going to tweak it since my wife nags me about it. I converted my house over to *. My setup: Compaq Deskpro EN SFF P3 500 Dual NIC for real IP and internal IP X100P Card for PSTN. Cisco ATA186 (two cordless phones for the old lady) Cisco 7960 Phone Cisco 2621 w/ 2 FXO's and 2 FXS (Fax is

Hello I'm using an older PC from 2000 that we have lying around at the office to learn about Asterisk using Pound Key 1.0.1 (http://www.rpath.org/rbuilder/project/asterisk/). It's using an AMD Duron 600MHz, a Gigabyte GA-7ZX motherboard, and two FXO Astralis X101P clones that I bought through eBay. Here are the three issues I have. Sorry, forgot the floppy with dmesg, lspci, and

Wow ! No reply... May be I must talk about X100P instead of X101P ? Is someone has yet encountered this kind of "no sound" problem when bridging two FXO lines like this (first as input, second as output) ? Any idea ? TIA. Best Regards, Francois BERGERET, France. ----- Original Message ----- From: "Francois BERGERET" <f6hqz-m@hamwlan.net> To: "Asterisk Users

Hi all, forgive the question but is it possible to use PCI modem cards (aka winmodem's) as FXO/FXS ports in * ? what about external modems like the USR Sportsters? Thanks in advance, Bryan. Bryan Nolen Lead Developer http://Arc.Net.AU http://cdonline.com.au

Hi We are trying to get better sound quality out of the prompts on our Asterisk system. We had some new ones made by thevoice.digium.com and they are in WAV format instead of the default GSM format on the Asterisk server. The problem is, when you dial in to the server using the FXO card (X100P) you really can't tell the difference between the WAV prompt and the GSM prompt, however, if you

Voxilla.com has a great config wizard for the SPA-3000 and * http://voxilla.com/spa3kasterisk.php I took the output from this wizard and dumped it on my test box with an SPA 3000 (with some mods to match my * contexts) and everything worked great. Calls from the PSTN to the spa3000 are routed to dialplan #8 on the spa3000, which dials * Both the FXO and FXS port register with * The SPA3000 is

Is there any advantage of getting a T1 card with a channel bank over 2-3 FXO cards ? Thanks. Dovid -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061031/0f74ec67/attachment.htm

Hi, I have found some cheap single port FXO Cards on ebay. They are apparently X100P compatible like the cards sold by Digium My question is 1) Are they any good 2) will 4 such cards work in a single * box without too much trouble? Thanks Andy

Hello, I'm looking for a dirt cheap solution for SOHO use to handle at most a couple of POTS lines, and I notice that X10?P cards go for $15 on eBay as opposed to $90 for an OpenVox card or over $200 for a Sangoma. I have a couple of questions about those cheap FXO cards: 1. Are they all glorified softmodems, ie. none has an on-board CPU or DSP and outsources all processing to the

I'm trying to add 2 FXO cards but when the second is added, asterisk stop to respond (zap channel): app_dial.c:545 dial_exec: Unable to create channel of type 'Zap' modprobe zaptel and modprobe wcfxo didn't return any error. ztcfg -vv is reporting only 1 card: Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels

we have got asterisk 1.0 (over 1 yrs old) version and very old zaptel version. That code is working only with 8 or less ports (accumulative) on digium fxs/fxo cards (2 cards with 4 ports each). the questoin is, what if we want 12 ports?..well, really, i don't understand the limitations? is it simply zaptel driver code fix? or kernel fix? or technology limitation? donno any tips would

Hi All, Channels 25-28 on a customers PBX are regular Zaptel FXO cards that are hooked into 4 incomming phone lines. They are all in a group to do automatic rollover for outgoing calls (if channel 25 is being used, dial on channel 26, etc.). Sometimes when a user is dialing a number, instead of bridging to one of the FXO cards it goes and rings to Zap/1-1. This doesnt occur all the time but some

> > First, ensure the TDM card has been defined to match the telephony > standards for each country where the card is installed. Bad echo on these outside North America is likely to be because of impedance mismatch. Echo cancel isn't likely to properly fix it. I was surprised at the lack of info about setting up the TDM cards for various countries. I eventually worked it out from a

Hello, I was trying to configure 2 Digium X100P-Card compatible FXO cards. Everything went OK up to starting Asterisk, the following error occures while parsing zapata.conf: Parsing '/etc/asterisk/zapata.conf': found Mar 27 16:24:20 ERROR[1075656544]: chan_zap.c:5196 mkintf: Unable to get parameters Mar 27 16:24:20 ERROR[1075656544]: chan_zap.c:7162 setup_zap: Unable to register channel

Saw an ad in the latest Linux Journal for Sangoma's FXO/FXS analog cards. it was part of an ad for a reseller. I can't find anything on the resellers site or Sangoma's site either. Did the ad jump the gun or someting? Is this for real? Paul -- Paul Dugas, Computer Engineer Dugas Enterprises, LLC paul@dugas.cc phone: 404-932-1355 522 Black Canyon Park