similar to: unable to send a fax to a given FAX number

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

I have a problem calling a certain number from our PRI line. Calling the number from a separate PSTN phone works fine. The remote number seems to have some funny call redivert setup, when you call it, it answers immediately, makes some kind of beep and then starts to ring. Our PRI is in the UK from Telewest/NTL/Virgin Media and most outgoing calls work without a problem. The server is

Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and

picture. I know the firmware on the Nortel is old, so I'm guessing that libpri is sending something that the Nortel does not know how to handle. Is there a way to dumb down what libpri sends? From everything I've read PRI is an evolving standard - and older devices may struggle with newer extensions/developments. (This might be very handy for users trying to talk to old pbx's.) Is

Salve, I'm somewhat stuck on how to get DTMF working with my setup and googling didn't yield anything similar. My setup consists of one CAPI-capable board (AVM Fritz!DSL) connected to a BRI (T-ISDN), one HFC-S board running in NT-mode connected to an internal S0 bus with some ISDN devices (DECT stations, TA) and, of course, some ethernet interfaces. ISDN standard used is Euro-ISDN.

Hi all, I'm debugging a PRI problem, i can see the calling number but i get a busy all the time. From the output below, I guess asterisk hangs up immediately. Can anyone point out what the problem is? Thanks in advance. *CLI> < Protocol Discriminator: Q.931 (8) len=32 < Call Ref: len= 2 (reference 4865/0x1301) (Originator) < Message type: SETUP (5) < [04 03 80 90 a3] <

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

Hello List I'm trying to figure out what is wrong between my asterisk and my NEC 2400 pbx We have been trying to link them with a spare PA-24DTG from the NEC, I'm able to call an extension on the Asterisk, however the extension rings, and then immediatly hangs up I traced it back to the debug of the PRI on the Asterisk... I would appreciate if anyone could pin point what is wrong The

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Hi, Running Asterisk 1.2.12.1 when dialing a known disconnected number the calls just rings and rings. We never get the "The number you are trying to reach...". If we dial the same number from an Asterisk 1.0.11 server again over PRI, we get the message on the 1st ring. Here is the PRI debug of such a call that just rings and rings. Any ideas? PRI debug sur CPL: -- Executing

Hi, Ive been playing on a asterisk to orion gsm box E1 pri setup. I have achieved incoming calls to be passed to my asterisk box successfully but outgoing calls will just I have tried playing with various pridialplan and overlapdial settings and with no success. If anyone can make more sense from the log, I'd certainly appreciate it. I am sending a 10 digit number to be dialed. I guessed

Dear Gurus, i am facing some unknown problem here.. first, let me describe my case. my office is using a nortel merridian option 11c PBX. and it is connected to the provider thru a E1 card, which is working fine with no problem. my plan it to slot in a server with 2 TE11XP card to intercept the outgoing calls. Provider <--te11xp---> asterisk <---te11xp------> nortel merridian

Hello, I have a problem, and I'm looking for you help. When I dial certain number my calls are getting dropped. I initiate the call, I hear IVR, then I am being transfered to operator, and then suddenly I get ISDN DISCONNECT message. I had this type of problem some time ago, and I thought it was a problem on the other end. But now this is a second time it occurred and I want an expert to