similar to: Call Park Logic?

Anyone ever seen MeetMe cause * to crash? Specifically, it happens consistantly if someone begins to enter a conference and then decides to hangup while Allison is introducing them - like playing back "conf-onlyperson". This has been seen with the MeetMe participant connecting via IAX and SIP (not saying it doesn't happen with Zap, just that I haven't seen it). The box is *

When trasferring a call, how is the context determined? When using a zap device, and the DTMF code for blind or attended transfer is entered, does the tranfer originate at the context the zap device is set to be in, or does it originate from where the outside call being transferred originated in, or the context the current call is in? I ask because I am seeing strange behavior when trying to

I set up a 4 digit extension for parking calls. 5400 All works fine from Asterisk. If I park a call from a legacy PBX, it parks OK and can be picked up, but if unanswered, the call parkingtime timer tries to send the call back to the PRI Zaptel trunk that it was parked with. That circuit is no longer in use. I can add a t extension for context 'park-dial' (which I assume is hardcoded

Dearest List, I guess I missed this point: Is it true that if you change the echo canceler in zconfig.h, and then recompile/install your zap modules, that for this to be taken into effect by * you must then recompile/install *? I would have figured that the zap echo cancellation method was independent of *, and I don't recall seeing any docs mentioning either way. Sincerely, Brent A.

Dollars to donuts it is related to these two posts, but no one seems to know where or why it happens - this issue doesn't seem to be related to one specific piece of hardware: Post 1) ********************************************************* Anyone ever seen MeetMe cause * to crash? Specifically, it happens consistantly if someone begins to enter a conference and then decides to hangup while

I've got a situation where I need to use a transfer to the parking lot as hold, but am not going to use BLF indicators on the phone to pick up the parked calls so I need to hear the 3-digit extension after the transfer. I'm using Snom 300 phones and have tried setting a programmable button to Key Event F_TRANSFER 700, which successfully does the transfer but cuts off audio so you

Can someone explain how to use groups? I can't seem to wrap myself around this, though I know it is something simple. I have 3 zap lines, and when placing an outgoing call, would like to 1) use a zap line if and only if 1 or fewer zap lines are being used at the time, and 2) if more than 1 zap lines are in use then to go ahead and use VOIP to place the call. Also, is there a difference

What would cause this? It happened out of the blue: -- Executing VoiceMail("Zap/3-1", "u326@default") in new stack -- Playing 'vm-theperson' (language 'en') -- Playing 'digits/3' (language 'en') -- Playing 'digits/2' (language 'en') -- Playing 'digits/6' (language 'en') -- Playing

Hello, Is there any way to park a call on a specific park number? If this is not possible, is there any way to create multiple park orbits? Also, is there any way to invoke call parking of an active call coming through a Zap channel from the manager interface? MATT---

I can't seem to retrieve a parked call. Here is what I do: Call from phoneA to phoneB Answer phoneB Press Flash/Callwait on phoneB Press 700 to park the call A voice says that the call is parked at 701 When I try to dial 701, I don't get connected to the parked call Below is the asterisk output when I tried to park

Well, I thought and hoped my issue of random hangups on our TDM400P were related to busydetect=yes in zapata.conf. The behavior of a call being hungup has not changed, however, since setting the busydetect option to 'no'. Again, the only affected user is my loud talker... What are some causes/solutions to seemingly random call disconnects on Zap channels that people have seen? I have

I have one use on our PBX who has been experiencing seemingly random disconnects. The user is on the same LAN as everyone else, using the same type of phone (79XX loaded with SIP firmware) as everyone else. He had some disconnects a few weeks ago, I suspected the phone, so I swapped his with mine. I have since not had issues with his old phone, however, he has had issues using mine. So, the

>Our user places a call, the gateway responds with no sound at all, or >hangs up, or gives busy tone. > >How can we get to the next provider? > >I have now: >exten => _9011Z.,103,Dial(SIP/011${EXTEN:4}@provider-a) >;exten => _9011Z.,103,Dial(SIP/011${EXTEN:4}@provider-b) >;exten => _9011Z.,103,Dial(SIP/011${EXTEN:4}@provider-c) >exten =>

Trouble in Parking Paradise! Good Day all, I have a situation that I have tracked as far as I can take it and am looking for assistance into the matter. My setup.. Asterisk 1.0.1 with the AMP config environment. When I have auto attendant answer the phone and I dial my extension "2204" The call come through and If I park it it gets place into extension 701 (the first parking

I have an issue with call parking and hope there is some undocumented feature for this. ;-) We are replacing our legacy PBX with asterisk, but to save money over time (handsets and network), I am trying to maintain the use of our legacy PBX. Asterisk extensions can not use the call parking features (not usable over trunk cards) of the old PBX, so I have to get the old PBX to use asterisk's.

Hi, I am having some trouble with parked calls timing out. In features.conf: [general] parkext => 800 ; What extension to dial to park parkpos => 801-820 ; What extensions to park calls on context=parkedcalls parkingtime=120 After the Park timesout it calls the phone that the call was parked from. If the phone is BUSY the call just get dropped. (Call waiting

Boy oh boy. This blows. I upgraded to 1.2.2 from 1.0.9, and of course had the timebomb bug. Immediately after upgrading to 1.2.3 we were ok, for 24 hours or so. Since upgrading to 1.2.3, though, the whole system has locked up twice. Once on Thursday, and then about a half hour ago. The server would reply to a ping, but no ssh login, no local console login - just locked up. This ain't good for

We are going to replace a BizFone with Asterisk and one of the features that I haven't been able to emulate is the PBX hold. We can put a call into hold with the * key and every 30 sec the phone gets a beep to remind us it is there and the caller on hold can hit # for other options. The closest I've come with Asterisk is call parking, and that doesn't quite do it. Using the

Ok I have read every line in the wiki for call parking. HELP PLEASE I need to perform a simple call parking that upon timeout will ALWAYS rings back to the extension that actually parked the call. Am I just crazy or is this not possible. >It has been narrowed down to the CONTEXT the call was originally located in. >I need to figure a way within the parking application to set the

It has been narrowed down to the CONTEXT the call was originally located in. I need to figure a way within the parking application to set the extension I want the call to ring back to. Specifically I want to set it to always ring back to the phone that parked it. Example, below .. When the call rings only a specific phone http://pastebin.ca/2452 the context it originates from aa_1,2204,1