similar to: IAX - FWD status

On Sat, 2005-06-18 at 13:17 -0700, Matthew Asham wrote: > For what it's worth I use a residential Shaw connection and have no > problems with IAX registration nor SIP to our Asterisk PBX elsewhere on > the 'net. When I had a dynapic IP connection with shaw, there was not problem either. I just changed to static and IAX can not connect. How can I test it? iax2 show registry Host

I just changed the from DSL to Shaw Cable (static IP) configure the firewall but now asterisk I can not register with FWD nor VoipJet calls going out. I am using IAX with FWD Did I missed to change a setting? I don't think there is any though. I am on shaw extreme connection; I just talked shaw tech. and they are not blocking any port - I was told. So why IAX will not register with FWD and

I find IAX connection with FWD very unreliable so I think I'll have to roll out my own "SIP Express Router" as I want to communicate with few SIP clients. So I hope this the right solution. I'm new to "SER" and to my understanding "SER is like a "road-map" it tells the SIP Clients where they are so they can communicate directly with each other without

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

What are the alternatives to FWD with IAX2 registration capability. FWD is great, but their IAX2 is not the priority and if it goes down it takes days to restore it. I want to use IAX2 protocol but the end point (Sipura unit) need to be able to register over SIP behind firewall. Line1 is registered with FWD PSTN need to be registered with somebody else. What are my alternatives? -- #Joseph

I'm testing Teliax tall free number line and I'm experiencing long delay about 1sec. during conversation. When I call myself over FWD the response is normal no delay or cut messages. When I call my number over FWD the is a long delay, welcome message usually cuts off few first words and during conversation my voice arrives after about 1sec. delay. Since, the 800-number is only accessible

Does anybody have a good link how to connect Sipura with Asteriks, both behind NAT? I'm using FWD but their connection is like a weather (especially IAX), I need something more reliable. I was thinking of using stun and/or proxy but can not find any good link explaining how to setup Linux server -- #Joseph

I'm just curious why Sipura isn't using free IAX protocol with their devices instead of SIP? With IAX NAT traversal would have been easier, so why are they using SIP. Is there any politics in it? -- #Joseph

Has anybody tried NVFaxDetect Fax detection for sip SIP/IAX channel? There is a new application from Newman Telecom for fax detection. http://www.sineapps.com/news.php?rssid=575 Current Asterisk Fax detection doesn't work for me as I don't have Digium cards; I'm using Siupra -- #Joseph

I have an incoming 800-number over IAX from Teliax and I'm experiencing the large packet loss on connection. When a call comes in there is no ring tone and the first few words of the welcome message are cut off, regardless of the delay I set. Standard call (not 800-number) coming over IAX with the same provider works just fine only the tall free number. So it seems there are some packet loss

Hi Folks, Just wondering if anyone can give me some pointers, I'm configuring Asterisk to talk to FWD's new IAX service. The asterisk server is behind an iptables NAT Firewall, with port 5036 forwarded: $IPTABLES -t nat -A PREROUTING -p udp -d $EXTERNAL_IP --dport 5036 -j DNAT --to-destination 172.16.20.200:5036 I can make outgoing calls just fine, but when I receive an inbound call

Good day all, I switched my SIP FWD account to IAX and connect my * in IAX. Working great, but I face one problem: I have an iaxtel account and try to call from there (iaxcomm) my FWD Iax # by 17009xxxxxx. It's ringing but no termination on my *. Calling 17009999612 or 17009<SIP FWD#> is working (SIP FWD# being an normal SIP account on FWD). Has someone some idea on what's

What dtmfmode should I set for IAX protocol? When I dial FWD over IAX it doesn't recognize the numbers I press. -- #Joseph

As described in: With NAT between Asterisk and FWD http://www.voip-info.org/wiki/view/Asterisk+How+to+connect+to+FWD Apparently it doesn't work, but I think the instruction is not complete. Is there a way do defined "Outbound Proxy" for FWD in sip.conf ??? Why do I need port forward 5060 and 10000 - 20000 to asterisk box? When I setup Sipura behind NAT (using NAT and proxy

I've setup my IAX2 over FWD and it is working I can receive a test call and I can call out. Though I cannot figure out how to dial 1-800 numbers over FWD When I dial 1-800 it hangs up on me. Here is a typical session: Called xxxxx:xxxxxxx@iax2.fwdnet.net/18007425877 -- Call accepted by 65.39.205.121 (format ULAW) -- Format for call is ULAW -- Hungup

Hi All, I am having trouble with receiving calls from FWD via IAX. I know this isn't a FWD support forum, but I suspect the problem is my asterisk setup. The problem is that I can dial out to fwd subscribers, even myself but they can't dial me using my FWD number. I don't know much about IAX, but it would seem to me like a registration problem, but I get no errors or warnings in

I have set up FWD via IAX service. I have tested the IAX service with 613, echo test, and 612, saytime. It all works well. However when ringing a FWD user, I got this error all the time: Connected to Asterisk CVS-v1-0-02/01/05-09:34:45 currently running on chat (pid = 8282) chat*CLI> Verbosity is at least 3 -- Executing SetCallerID("SIP/1001-a1fb", ""David

Hello, In my sip.conf I have: ;Register and forward FWD numbers to internal extensions register => FWDNUMBER:PASSWORD@fwd.pulver.com/9500 Which should register Asterisk at FWD and then when any calls are made to FWDNUMBER those calls should be forwarded to extension 9500 as specified in the extensions.conf. What I am getting is it is trying to dial the 9500 (IAX Firefly) client twice when

Is anyone here able to make calls to FWD via IAX? I haven't beenable to for some while. I'd like to get to the bottom of the problem. There's been little response in the FWD support forum thus far. I can call my own number and it rings my server, but I cannot call any other number. It generates and error reporting "everyone is busy at this time." Michael -- Michael Graves

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.