Displaying 20 results from an estimated 200 matches similar to: "help with no audio"
2008 Sep 26
2
server and 2 uniden phones no ringing
I have a box running asterisk 1.4.17 that had been working.
it has 2 uniden phones connected on it.
This was working and now the phones dont ring when calling each other.
below is the sip debug. I cant see why the other phone does not ring?
I also tried changing the canreinvite for no to yes but that made no
difference after restarting.
Very simple network. server, linksys router and 2 phones.
2007 Nov 20
0
sl75 wlan not able of being pickuped?
Hello.
I have a strange problem. Its not possible to pickup a call that was placed
with a Siemens SL75 Wlan. When this phone calls an internal number and i try
to pickup (*8) the call from my phone i get nothing. It seems i have the call
for one second or so but after that the call is being cancelled. No problems
with other phones (polycom, grandstream). Attached the complete sip debug log
2010 Aug 02
6
Codec negotiation : expecting G726, getting G711a (alaw)
Hello list,
Grandstream GXP2010 phone calling to Snom 320, Asterisk in the middle.
Grandstream allows for 8 different codec specifications. I have defined
them as 4 x G726 & 4 x alaw.
Snom allow for 7 different codec specifications. I have defined them as
3 x G726 & 4 x G729.
The SIP peers are both defined as :
disallow=all
allow=g726
allow=alaw
allow=g729
allow=gsm
This is the
2010 Jul 12
4
Remote-Party-ID party=called
Hello list,
using Asterisk 1.4.30.
I want to set the SIP-header Remote-Party-ID to display the name of the
calling party on my phone in stead of the number.
This is the dialplan :
exten => 10,1,NoOp()
exten => 10,n,SIPAddHeader(Remote-Party-ID: "eric"
<sip:10 at 192.168.1.150>;party=called )
exten => 10,n,Dial(SIP/test2)
This is what the CLI shows :
/[Jul 12
2004 Jun 27
5
Optipoint 400 Standard Sip
Hi everybody,
I am testing Optipoint 400 Standard SIP (Firmware 2.3.14) with Asterisk.
It is posible to dial from another Phone (x-lite) to the Optipoint, but when I try to dial from the Optipoint there is no dialtone and there is only a short beep when I dial Numbers.
The Optipoint shows "no Server..." (Registrar?) in Display.
Sip debug shows no unusual (to me) Messages.
Sip show
2006 Nov 23
1
asterisk 1.4 chan_h323, help please...
Hi,
My configuration is SipPhone<-->*1<--->*2.
My asterisk version is 1.4beta3.
I installed pwlib,openh323,chan_h323.
When i call from
SipPhone--(SIP)-->asterisk1---(H323)-->asterisk2,
there is no audio.
Using 'rtp debug', I can see that rtp packets are
being received.
Rtp packets are being exchanged.
I also tested chan_ooh323, but to fail.
Can anyone recommand best
2011 Jan 26
0
list of errorswhile registering client at asterisk with sipp
Hi every one,
Hello i am doing project on evaluating the sip proxy
performances like asterisk, openims and opensips using the traffic generator
SIPp.
I am using 2 computers of same configuration as SIPp clients one as uac and
other as uas... and one laptop for asterisk server......
UAC:192.168.1.99------------------------>Asterisk
2004 Jun 30
1
Using Asterisk as H323 gateway
Hi there.
I am trying to connect Asterisk to a local danish ip-telephony provider.
But is having some difficulties. First I thougt they were related to the
provider. But then i started debugging on the Asterisk (aix2 debug)
When I make a call using AIX to the provider everything seems to work
just fine:
*CLI> -- Accepting AUTHENTICATED call from 192.168.1.150, requested
format = 1024,
2006 Oct 18
0
[OT] Nokia E60/61/70 and SIP
Martin Joseph wrote:
>
>
> For all of us using these devices, I have some good news. There is a
> self installable firmware update available from Nokia here (requires
> windows box to install):
>
> http://www.nokia.co.uk/nokia/0,1522,,00.html?orig=/softwareupdate
>
> This seems to radically improve the behavior of the SIP client on my
> E60. It seems to have
2004 Nov 30
2
problem with cached netbios name of wins server
fc2, samba 3.0.9
The samba server is PDC.
Temporarily, the server was dhcp, which gave it the IP
192.168.1.64
we then set it to static 192.168.1.150, which is what
we want.
however, the different windows clients, on and off, on
ping and such, resolve INTRANET, the netbios name of
the pdc, to 192.168.1.64 still, despite me removing
wins.dat.
I even tried the following suggestion, to no avail
2007 Feb 21
1
simple source policy routing not working
Hi,
my box is connected to 3 networks, eth0 eth1 wlan0. I want "my" traffic to go
via wlan0 and everything from eth1 NATed to eth0:
eth0 192.168.1.10/24
eth1 172.16.1.1/12
wlan0 192.168.10.190/24
I first tried this with two single hosts:
iptables -A POSTROUTING -j MASQUERADE -o eth0 -t nat
iptables -A POSTROUTING -j MASQUERADE -o wlan0 -t nat
echo 200 Forw >>
2005 Jun 30
0
linux pdc two subnets over vpn almost working, but not quite
Ok, I have linux samba pdc wins server
192.168.1.150
behind a cisco router(192.168.1.1). everything else
behind that router works fine, clients look at
192.168.1.150 as WINS server.
vpn over to netgear router(192.168.2.1), with
192.168.2.x subnet. the netgear tells all dhcp
clients to look at 192.168.1.150 as WINS server.
clients on 192.168.1.x network can ping clients on
192.168.2.x network
2006 Aug 16
1
Building a basic router with two nic's
I need help setting up a basic routing between two nic's on my CentOS
desktop. I thought I'd understood the basics, but ... I don,t want a nat
router, just packets forwarded back and fort.
This is what I thought would do the trick, but didn't. Can someone
please give me some pointers or links so I can get this right.
# echo "1" > /proc/sys/net/ipv4/ip_forward
# route
2010 Feb 07
2
problems with samba share
Hi everyone,
I want to achieve the following setup:
- have a share that is read-only and accessible for guest users;
- have the same share be modified by an authenticated specific user.
This is running on debian lenny, samba 3.2.5.
My smb.conf is as follows:
[global]
workgroup = WORKGROUP
netbios name = cast
remote announce = 192.168.1.99/WORKGROUP
server string = %h
2001 Nov 21
1
No writing to [homes] share
I upgraded from version 2.2.0 to 2.2.2 and since then no one can write
to their home directory. Attached is a log (at 3) and smb.conf for
reference.
Also profiles aren't working for Windows 2000 SP2 machines. Any ideas?
Thanks in advance for any help
Chris Tooley
-------------- next part --------------
# Samba config file created using SWAT
# from 192.168.1.50 (192.168.1.50)
# Date:
2019 Aug 26
2
Extend DHCP range
I have a simple DHCP range .
option routers 192.168.1.1;
subnet 192.168.1.0 netmask 255.255.255.0 {
range 192.168.1.60 192.168.1.129;
range 192.168.1.150 192.168.1.199;
}
So I want to add a range 192.168.2.1 -> 192.168.2.254
so I did this:
subnet 192.168.1.0 netmask 255.255.254.0 {
range 192.168.1.60 192.168.1.129;
range 192.168.1.150 192.168.1.199;
2011 Aug 26
0
Using of bonded interfaces for xen dom0 (debian)
Hello,
Where can I find a link (or docs) to *working* network config for xen 4.1.2?
My tests (s. below) were not successful.
Thank you in advance for any hints.
Regards, Mark
# ---
root@xen411dom0:~# cat /etc/network/interfaces
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
auto lo
iface lo inet loopback
auto bond0
2018 Apr 02
1
Much improved speeds of rsync via SSH - something to consider
Dear rsync devs,
I recently concluded a bug hunt to trace why my rsync-ing to an SBC was
much slower than the corresponding iperf3-reported speeds. To give a
concise summary of the situation, in slow wifi links using SSH with
ProxyCommand tremendously speeds up things:
$ dd if=/dev/urandom bs=1M count=50 of=sample.data
50+0 records in
50+0 records out
52428800 bytes (52 MB, 50
2006 Aug 04
0
net rpc rights ¿problem?
Hi!
I have a domain with samba+ldap working perfectly. The LDAP and Samba are in a linux
vserver machine, but in the main host, not in the guests. The machine has samba 3.0.22 and
debian sarge 3.1 up to date. Last week I try to assign privileges to different users with
the 'net rpc rights' command and found a strange behaviour.
('asier' is a local user without privileges, not
2010 Mar 11
2
Codec preference
How can I set the prefered codec between 2 calling parties ??
My Grandstream supports G729, alaw and gsm... in this order.
The Zoiper softphone has alaw and gsm as codecs... in that order.
Although there should be a matching codec found, my Grandstream can not
call the Zoiper softphone.
CLI shows :
[Mar 11 17:47:21] WARNING[22367]: channel.c:3340
ast_channel_make_compatible: No path to