similar to: asterisk-users Digest, Vol 44, Issue 104

All too common and largely undocumented. I had this same problem. Installing ztdummy changes Asterisk to use it for timing of playback, apparently. Removing ztdummy "fixed" the problem. To get it all to work, I had to upgrade to to at least kernel 2.6.23.11 (previous versions are either missing options are just broken.) After doing this, I recompiled ztdummy and it worked. Note

What does it take to get ztdummy to work correctly? I have a new laptop HP HDX9200. I am running asterisk 1.4.19 and zaptel 1.4.9.2 Zaptel compiles fine. asterisk compiles fine. ztdummy loads asterisk runs. Problem is playback() does not work. So then I stop zaptel, asterisk runs and playback() now works. However, meetme()'s dont work. I need ztdummy I'm pretty sure for that. I am

On Mar 19, 2008, at 1:00 PM, asterisk-users-request at lists.digium.com wrote: > Am I expecting too much? Perhaps. I think the hardware on which we run Asterisk can be much more reliable than the software, which is often the case. We have a bunch of HP servers with RAID and have never lost anything. A HD may fail, but the RAID keeps it going until we pop a new drive in there. A

I tried to test Asterisk 1.4 on FC6 x86_64. I have it working on FC5 x86_64 very good, but since FC keeps updating, I tried to follow newer kernel versions. I can't pass the zaptel compilation. Everything is OK, but when I finished, and tried to load it, allways got module not found when I run modprobe zaptel, and modprobe ztdummy. I already tried to modify is with the sed 1 option but

I've encountered an odd situation with Asterisk 1.4.19 that I can't figure out. If I dial an extension via a Cisco AS5400 with the "g" option to come back, when I then Dial another extension after that, we don't get audio from the caller. There are no firewalls, no routers, no anything but a network switch between. The calls come in as SIP from the Cisco and

Has anyone got a Premisys Slimline channel bank working with a Cisco AS5400 or similar? I'm not sure if my unit is bad, or what. I'm using FXS Loop Start. Calling the port connects immediately without ringing the attached phone. If I pick up the phone, it's connected and I can talk to the caller. Hanging up has no effect. I can see the bit transitions (0101 to 1111 when I go

On Mar 5, 2008, at 5:46 PM, asterisk-users-request at lists.digium.com wrote: > If you are running a call centre (large or small) using Asterisk, > I'd be > interested to know how you log your agents in & out: > > E.g. > > - Do you use AgentLogin (to force calls onto the agents, perhaps)? > - Do you still use AgentCallbackLogin? > - If you use

I've been searching to a solution to this for a while and can't figure it out, perhaps someone has done something similar. I have a Cisco AS5400 sending SIP traffic via PCMU / ulaw directly to my Asterisk (1.4.19-rc2) box. Jitter and latency are incredibly low on my lightly loaded switched gigabit ethernet network. One Asterisk uses Zaptel and a Digium card, and DTMF recognition

Note that the newish SPA962 has 6 appearances and a color screen. I've noticed that the bright color screen does impress people when they first see it. PoE is also very nice and web provisioning was quite easy. I've yet to try a more automated provisioning method on it. I know that getting the polycom's to auto provision wasn't very straight forward. I do provision some

On Oct 16, 2008, at 2:36 AM, asterisk-users-request at lists.digium.com wrote: > I want to call an extension like 88888 and invoke an external C > program upon > calling, pass an constant integer like 1 to the C program. > > What I have done is: > > /etc/extensions.conf: > exten => 88888,1,system(/usr/local/src/parallel/fire 1) > exten => 88888,n,

Hi, I've install zaptel and I don't have a Digium card installed in the machine. So I want to install ztdummy to have Music On Hold working. I've follow these instruction http://www.voip-info.org/wiki-Asterisk+timer+ztdummy and at the point "modprobe ztdummy" it's failing. I'm getting these messages: root@dubic:~# modprobe ztdummy FATAL: Error inserting ztdummy

Hi all, Trying to build ztdummy on an old redhat 7.3 box running kernel 2.4.20-43.7.legacysmp. Yes, I have the kernel sources installed. Yes, I set them up with make oldconfig; make dep. The build error is: make ztdummy gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB -I/usr/src/linux/drivers/net -Wall -I. -Wstrict-prototypes -fomit-frame-pointer -I/usr/src/

Hi all, I hope everyone is doing well. I just joined the list, and I've really enjoyed all I have read about asterisk so far. Unfortunately, I'm having a bit of trouble implementing this thing :). By the way ... I did my best to search the forums, and also to use google extensively, and while I have found pages with people with the same problem, ... The fix suggested on those sites,

Has anyone received this message while attempting to do a MAKE INSTALL on ZAPTEL depmod: *** Unresolved symbols in /lib/modules/2.4.26-gentoo-r9/misc/ztdummy.o I am not running DEVFS so that's not the issue. Zaptel drivers/modules all load, but ztdummy won't /lib/modules/2.4.26-gentoo-r9/misc/ztdummy.o: /lib/modules/2.4.26-gentoo-r9/misc/ztdummy.o: unresolved

Hi i followed this instructions for installing ztdummy on a 2.6 kernel (taken from http://www.voip-info.org/wiki/index.php?page=Asterisk+timer+ztdummy ) cd /usr/src/zaptel * READ /usr/src/zaptel/README.udev and follow the steps * check modules on: /etc/sysconfig/zaptel> if you have no digium hardware comment out all modeules except ztdummy. - make linux26 - make install -

Hi Everyone, I read through the list on the issues with the ztdummy driver which I need for MeetMe, but I seem to have come across a problem that I cannot seem to find an answer for. I am running Gentoo 2.6.10 on an Intel box. I have read the the wiki entries on the ztdummy and followed the instructions as they relate to the 2.6 kernel. Everything compiled great, but a modprobe ztdummy

Hi! When I try to load the ztdummy driver via "insmod ztdummy", I get the following errors: /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_register I'm using zaptel-1.0.8 and

Hi to everybody, seems that I cannot load the zaptel modules: ztdummy says the following: [root@Hayabusa misc]# modprobe ztdummy /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_register

I've been evaluating Asterisk for a while, and things seem to be going very well. The issue of redundancy and automatic fail-over is now on my mind. I searched the archives and googled for solutions, but didn't really come up with much. We'll be using queues (modified), which precludes some of the standard redundancy solutions, since the queue needs to know all the agents

Hi I run asterisk 1.4.2 with zaptel 1.4.1. Zaptel is only needed for the ztdummy driver to get the Meetme() application to work. I don't have any specific hardware. And it does work nicely. When I reboot the machine however I have to manually load the driver like this: [root@vink ~]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device