similar to: Polycom 301/501 Keymapping

Hello all, I was wondering if anyone has had much experience with Realtime Asterisk. I like the ability to setup my extensions and voicemail boxes in MySQL, but I have a huge worry. What if MySQL crashes. I played with rtcachefriends, but can't seem to find a way to have asterisk store the extension information to ensure the phones will continue to work even if MySQL has a hiccup. Any

So I might have a bit of a more narrow question from my earlier one. Previous, I had been wondering what would cause a phone dialing into a DID that connects to the asterisk box to get a fast busy. I've noticed the following message: chan_zap.c: Ring requested on unconfigured channel 0/1 span 2 Any idea what would give me this error? And would this cause a fast busy? Thanks again everyone

We have a location that is having a really odd issue. We have a sangoma POTs card. We are running software echo cancellation with the card (through asterisk) to try to eliminate some major echoing problems. I've turned on both EC and echotrain, which seemed to have gotten rid of the echo for the most part. However, we are now running into an issue where the outside caller hears a star wars

I'm sure this was asked before, but I can't seem to make this work... If a customer dials one of our DIDs, and the operator transfers that call to another employee, the Caller ID doesn't seem to do what I would expect it to. I would expect it to show the original caller's ID. Example: John calls in from the outside using (213-555-1234) and he calls into the asterisk system

Hey all, I had a user complaining of calls which were dropping mid-conversation. I looked into the time of one of the calls, and saw the following: Apr 4 12:13:03 WARNING[6670] chan_zap.c: No D-channels available! Using Primary channel 28 as D-channel anyway! Apr 4 12:13:05 WARNING[6660] channel.c: Avoided initial deadlock for '0x82b8430', 10 retries! Apr 4 12:13:05 WARNING[6660]

We are trying to use a softphone from a location that is behind a firewall. We are using x-lite as the softphone. So far, we've been able to get the phone to register with the asterisk server, and it can receive voice from the asterisk server (IE, voicemail, etc). However, asterisk can't hear anything from the softphone. We have used 2 different machines to test this on. We are watching

I'm trying to duplicate a behavior we had with our old avaya system, and I've come across Auto Answer (Ring Answer). However, its not quite the same yet. Right now, when I dial **5053, it will add the SIP header for Ring Answer and it will call 5053. The phone auto pickups just fine. However, we need that call to be muted. If you were to call into a meeting, we wouldn't want them to

I've been able to page to a specific phone (intercom type of thing), but I'd like to have a macro or agi that pages all phones but first checks if their on the phone. It looked like there used to be a pageall.agi type of script on the wiki, but that link isn't valid anymore. Does anyone have that script, or something else that would work? I would just do SIP/1000&SIP/1001, but

Hi all, Here's our setup: Asterisk 1.4.18 Agx-ast-addons 1.4.5 Problem: When accepting a fax, the fax itself comes through just fine, and it does successfully create a tiff file. However, the dialplan should be executing a system command right after that completes, but isn't due to hanging up early. I'm getting a cause 16 hangup, which I believe is a "Normal Hangup", but

I'm having a problem getting my queue to function as it should. After 20 seconds or so, it should prompt the user with a message "thanks for holding..... press # to leave a message or stay on the line to continue holding". I set up the "context" in the queues.conf file, so if a user presses a digit, they should be able to leave. But I get a SIP BUSY message. Here are my

Hello All, Hoping all of you might have an additional option for me to try at this point. :) My Goal: To have a paging option that does the following.... When I press **_XXXX it will send a ring-answer page to that person. The person on the other end should be muted, so if they are in a conference, you can't hear what is going on in the meeting. If that person hears me and decides they want

Hoping someone out there has run into this or has some ideas for us. We currently have asterisk set up with Realtime (using mysql) for its extensions,sip and voicemail files. The problem we are trying to solve, is one of a failover mechanism. What if our mysql server went down. Can Realtime be set up with a secondary mysql server to get its data from. We can set up mysql to sync with its fellow

We're trying to get a SIP peer going between our asterisk box and our provider. It should then ring our phone. The call does come in and it does execute the extension in the dial plan. But the provider says they never get a 200 OK back and therefore they send another INVITE and then after a few seconds drop the call. Here's our setup: sip.conf [ngt-trunk] type=peer qualify=yes port=5060

Hi, I just got a Polycom 330 and, of course, I don't have the firmware and sip.cfg files to provision it. Where can I get those? Mike -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070605/a14615c8/attachment.htm

Anyone use the LDAP feature yet on the polycom phones? If so how well does it work? How are you using it in your environment? http://polycom.com/usa/en/products/voice/desktop/soundpoint_ip/applicati ons/corporate_directory_access.html Roy Anciso Director of Technology Manistee Intermediate School District 772 East Parkdale Avenue Manistee, MI 49660 Ph: 231-723-4264 Fx: 231-398-3036 roy at

Hello all, I need the bootrom.ld file to set up some Polycoms I have Platform: Model=SoundPoint IP 330, Assembly=2345-12200-001 Rev=A I've publiched on my FTP files downloaded from http://support.polycom.com/PolycomService/support/us/support/voice/soundpoint_ip/soundpoint_ip330_320.html (3.2.3 combined and split zips) but my phones are still showing the message: "error, application is

<Correction in my zapata.conf file I used> Hey Everyone, So this is a problem I've been having for sometime now. I sent a few messages to the list with no luck. The problem is that when people dial into the Asterisk system using DID numbers, it works the first time or 2, then I get busy signals. A friend recommended I clear out the zapata and zaptel, start over, and recreate my

Hi Guus, hi all, please find attached a proposed feature implementation for tinc. As mentioned in http://www.tinc-vpn.org/pipermail/tinc/2010-May/002344.html , my goal was to connect nodes on the same LAN using their local (LAN) endpoints. I've implemented a multicast sender, which announces its own endpoint on every connected interface regularly. All nodes receiving multicast

I have provisioned a bunch of Polycom 301 phones to get the config files from my ftp server. Out of the 4 phones 2 get the config file however the other 2 cannot contact the boot server. I have reboot the phones a number of times remotely (the client is 400 km away) through vnc and logging onto the web config internally. No matter what I change on the web config page it is not saved. I feel I

Hi All, I have this small doubt. Does backgroundrb have anything to do with dispatch.fcgi? some dispatch.fcgi are taking memory as much as 186 MB .... this is monstrous man... Also, if i put load rails environment with backgroundrb.yml file to be false.What will happen? i just loses access to db through ActiveRecord right? I can still use normal mysql gem to access db and modify the