similar to: DialPlan help with Analog Fax Machine

Hi, I have two local SIP extensions (both bt100). One is on remote location behind another nat (16), but everyithing seems to be setup correctly as it can register and is listed as OK(57ms). However I can only call in one direction between those two. Extensions are defined in same context: exten => 11,1,Macro(oneline,SIP/11) exten => 16,1,Macro(oneline,SIP/16) both using same macro

I have an X100P clone hocked up to an analog line of my PRI. I can use it to dial out. but when I call the extension it answers and says "GOODBY" I have a Livevoip DID which successfuly rings to ext 202 I am using asterisk@home and through the AMP inface the line should ring to ext 202 Below are Asterisk Messages, Extensions.conf and Extensions_additional.conf Extensions.conf

Andi - I have experienced the same issue you mention and gotten no reply as to a way to fix it. I finally implemented "blacklist" into my Asterisk and added "Anonymous", "anonymous", "unknown", "Unknown", etc., into my blacklist file. When those come in with an IP address instead of a phone number but have no real name, they get the

Hello, i am trying to enable call forwarding on asterisk 1.6 with asterisk-gui If i set my stdexten as follows (with the lines i marked) everything seems like working. But if i make any change on asterisk-gui and apply it.. it recreates the macro-stdexten and deletes my configuration regarding to it. So where should i add my call-forward configuration??? Where am i making a mistake??

Hi! Trying to figure out what I am doing wrong... 1 std SIP phone (0317998975) registered to an Asterisk (SVN-trunk-r234256) 1 Cell phone 00733025975 attached through H323. extensions.conf exten => 975,1,Goto(975-${DEVICE_STATE(SIP/0317998975)},1) exten => 975-INUSE,1,VoiceMail(0317998975 at inputinterior.se,bs) exten => 975-INUSE,2,Hangup() exten =>

Hi! Have a weired problem with Avaya 9650 phones: extensions.conf exten => 0317998975,hint,SIP/0317998975 exten => 0317998975,1,Goto(0317998975-${DEVICE_STATE(SIP/0317998975)},1) exten => 0317998975,2,Hangup() exten => 0317998975-INUSE,1,VoiceMail(0317998975 at inputinterior.se,bs) exten => 0317998975-INUSE,2,Hangup() exten => 0317998975-NOANSWER,1,VoiceMail(0317998975 at

I think you will find the functionality you are looking for is in * already. Here is an excerpt from the sample extensions.conf file that is included with the source: exten => s,1,Dial(${ARG2},20) ; Ring the interface, 20 seconds maximum exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER) exten

Hi, im using a Asterisk Server which is not behind NAT. First i had problems with the fax detection. But this is now solved after adding a wait(2) at the correct place. But i'm still unable to receive a fax due to res_rtp_asterisk.c:3548 ast_rtp_read: RTP Read too short after the Fax session has started. My sip.conf includes [general] allowguest=no alwaysauthreject=yes sendrpid=rpid

How do I get a context to continue to execute commands after the caller hangs up after a Dial command? I'm using the "e" option to the Dial application. I though the "e" option would allow the context to continue. This doesn't want to work for me. I'm using asterisk-1.6.beta5 I never get to "3" below. I get a message saying the "2" ended

Dear all, Anyone get the lastest spandsp with udptl.c and tpkt.c compile in Fedora 3? tpkt.c: In function `accept_thread': tpkt.c:140: error: `TCP_NODELAY' undeclared (first use in this function) tpkt.c:140: error: (Each undeclared identifier is reported only once tpkt.c:140: error: for each function it appears in.) tpkt.c:144: error: invalid application of `sizeof' to

Hello, We have a strange situation (asterisk 1.6.2.14), where we get a result for DIALSTATUS for BUSY and No-ANSWER, but nothing for CANCEL. This is the (relevant) test dialplan: -------------------------------- [incoming-private] exten => _X., n, Dial(SIP/1001,30) exten => _X., n, NoOp(${DIALSTATUS}) exten => _X., n, Gosub(incoming-status,s-${DIALSTATUS},1) [incoming-status] exten

Dear list, I've got the following setup : [FAX-ATA]--[PBX LAN]--[Firewall]--[PBX WAN]-----[upstream SIP] On the PBX's we run Asterisk 1.4.33 with t38pt_udptl=yes in [general]. The FAX ATA is a Teles VoIPBox with T.38 support (that works). On the PBX WAN, i see the following in udptl debug : Sent UDPTL packet to 172.16.0.156:4460 (type 0, seq 184, len 32) Got UDPTL packet from

Hello, We're trying to receive faxes on the Asterisk server, but for the time being T.38 negotiation fails. The SDP that the Asterisk reINVITE sends contains these lines: ---------------------- m=image 4968 udptl t38 a=T38FaxVersion:0 a=T38MaxBitRate:9600 a=T38FaxFillBitRemoval a=T38FaxTranscodingMMR a=T38FaxTranscodingJBIG a=T38FaxRateManagement:transferredTCF a=T38FaxMaxDatagram:1400

Calling from my home using Asterisk 1.6.2.1 to an office extension (Asterisk 1.6.1.13) the callerid is not honored: Home: -- Starting simple switch on 'DAHDI/1-1' -- Executing [170 at internal:1] Answer("DAHDI/1-1", "") in new stack -- Executing [170 at internal:2] NoOp("DAHDI/1-1", "Context: office-extensions") in new stack

Gentlemen, I have 3 faxes attached to an Asterisk. Fax - SPA2102 - Asterisk. 0851711201 and 0851711290 is on our WAN, no NAT. 0197673581 is outside our WAN and needs to be NAT'ed. Sending a fax from 0851711201 to 0851711290, no problem, switches to T38 and fax goes through. Sending a from 0197673581 to 0851711201, no problem as long as i dont enable T38 on 0197673581. But, if i enable T38

Hi All, I've been testing reliability with t.38 faxing pass through with * 1.4.21.1, Linksys ATA's 2102 x 2, Sharp UX-B800SE and Cannon ImageClass D880. cannon> <2102 #1> <SIP> <*> <SIP> <2102 #2> <sharp Started out with default settings on all devices, configured Asterisk to handle T.38 pass through, the configuration I believe is solid. I get

Hi, I have following one-line macro extension: ------------------------ [macro-oneline] ; ; Standard extension macro (with call forwarding): ; ${ARG1} - Device(s) to ring ; #exten => s,1,AGI(misterhouse.agi,"CallerID") exten => s,1,NoOp exten => s,2,DBget(temp=CFIM/${MACRO_EXTEN}) ; Get CFIM key, if not existing, goto 103 exten => s,3,Dial(Local/${temp}@default/n) ;

On Fri, Jun 16, 2017, at 10:49 AM, Michael Maier wrote: <snip> > > t38modem and asterisk are using > > m=image 35622 udptl t38 > ^^^^^ > > Provider uses > > m=image 35622 UDPTL t38 > ^^^^^ > > Could this be a problem? If I'm sending internal only, it's always > lowercase. Looking at the tests we have we

Hello guys. When I am trying to send fax through T38 to linksys SPA (properly configured etc. - I have tried it with other systems), I'm getting error and fax is not delivered. I'm getting this errors in asterisk.log: WARNING[687] udptl.c: No UDPTL ports remaining ERROR[687] chan_sip.c: UDPTL creation failed WARNING[687] udptl.c: No UDPTL ports remaining then, couple lines down:

Here is an example of a couple of macros that help me where I have a SOHO with a home phone line and a work phone line. If I pick up line 2 my work line I would prefer the call I make to go out my office phone line same with if I pick up line 1 my home phone line I would prefer it go out my home line but want it to roll if needed. So with this little macro it is possible for that to happen.