similar to: HP proliant and hpasm

Hi there, Running patlooptest following instructions on Digium KB, using dahdi 2.5.1 with a TE205P. I'm getting this kind of output (not full output). Note, I'm using a standard cat5 ethernet cable (30cm), with a Digium T10i crossover. Error 4985 (loop 19898, offset 425, error 214): Unexpected result, Read: 0xff, Expected 0x00. Offset 422 { ff ff ff ff ff ff ff } Error 4986 (loop

Hi! I've installed Centos 4.4 on a machine at work (it's a HP Proliant DL-320 G2 rackmout server that serves my desktop). In recent days (Centos 4.4 has only been installed for a little over a week), like, since Wed or Thu last week, every time I reboot Kudzu wants to remove the network adaptors then reinstall them and breaks the network. I've gone to the point of disabling one of

Does anyone know if patlooptest either doesn't work for fxo/fxs signaled channels or if you have to do it a different way? If I run ./patlooptest /dev/zap/25 60 with a config like: fxsks=25-32 fxoks=33-48 it gives me a bunch of output along the lines of: (Error 4071): Unexpected result, 254 != 255, 11 bytes since last error. (Error 4072): Unexpected result, 0 != 255, 1 bytes since last

Hi Does anyone have experience of running CentOS on HP hardware, both rack mount kit and blades? How are things like hardware monitoring etc? We may be moving from Dell to HP and i get on really well with OMSA and Nagios etc so ideally would like to monitor using similar tools rather than some central 'enterprise' dashboard etc. Any real world experience? thanks

In article <CAHZ_z=w5DMg93gShtC93kuC+fnmraPgV46BS956U5BQXVgyhxg at mail.gmail.com>, Matt Fredrickson <creslin at digium.com> wrote: > On Tue, Apr 3, 2018 at 5:44 AM, Tony Mountifield <tony at softins.co.uk> wrote: > > I have some more investigation to do on this, but I wanted to see if anyone > > here had any insight into the issue I've run into. > > >

Hi List. I'm running the patlooptest program I've found in dahdi_tools 2.1.0.2. The target is a TE121P board with a loopback cable inserted on the socket. I suppose that the loopback is working fine because I'm able to see the green led on and dahdi_tool reports no errors. When I run the patlooptest I've a lot of errors (the received values are completely different than the

Hi all, I have setup a Dell PowerEdge 2550 with a Sangoma A200 card with 2xFSO and 1XFS modules. The PowerEdge specs are 1 x P3 1133MHz, 512MB RAM. Sangoma A200 has 3 analogue PSTN lines connected. This server is based in Office 1, with 5 users all with a Linksys SPA942 VoIP Handset. There is another Office (Office 2) connected to here using VPN. There are two users in Office 2 with the

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

hello: I wan to use the test tools-patgen and pattest for pri cards. according to Tzafrir Cohen from http://docs.tzafrir.org.il/man/pattest.8.html, i still does not know how to use that. do i need to connect two pri cards with two servers, or use a cable to connect two cards in one server? please give me a more details in term of cables and configurations. thanks! Chris -------------- next part

I'm running up-to-date CentOS 5 w/ Xen. I'm getting tons (tons = 13787 just yesterday, presumably because I have a monitoring system poll every 5 minutes) of log entries of the following: netsnmp_assert index == tmp failed if-mib/data_access/interface.c:467 _access_interface_entry_save_name() and netsnmp_assert rc == 0 failed if-mib/ifTable/ifTable_data_access.c:209

I have some more investigation to do on this, but I wanted to see if anyone here had any insight into the issue I've run into. The hardware is a HP DL360 G6 with a TE420 gen 5 4-port T1 PRI card. It is one of several systems that have been running without issue since 2010/2011. They have all been running CentOS 4 32-bit with Zaptel 1.4.12.1 (with patch for gen 5 card), libpri 1.2.8 and

I've been working with Digium, but hopefully someone on-list has an idea... The card will transmit audio to the T1, but everything it receives is completely unintelligible static (in place of received audio only, not all the time). I've verified everything on Digium's troubleshooting checklist and they were unable to find anything when they logged in. zttest yields 100% for the

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

It seems I can't smarm monitor disks on RAID controllers? I tried on several machines with two different controllers and on all I get this when starting up smartd: Jul 27 14:36:43 c1 smartd[5944]: Opened configuration file /etc/smartd.conf Jul 27 14:36:43 c1 smartd[5944]: Configuration file /etc/smartd.conf parsed. Jul 27 14:36:43 c1 smartd[5944]: Device: /dev/sda, opened Jul 27 14:36:43

I'll keep asking weird questions here: I have two T1 WAN circuits originating at my asterisk box and terminating at Asterisk servers at remote sites. Currently I use zaptel ppp assigned to all 24 channels for data. Now I would like to split off a few of these channels for voice trunks (I should use VOIP, but at the moment I do not have fast enough servers for the codecs) At one site

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.11.0-rc1 DAHDI-Tools-v2.11.0-rc1 dahdi-linux-complete-2.11.0-rc1+2.11.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * This release

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.11.0-rc1 DAHDI-Tools-v2.11.0-rc1 dahdi-linux-complete-2.11.0-rc1+2.11.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * This release

I am running Asterisk 1.16.2.13, dahdi 2.4.0 and libpri 1.4.11.4 on an HP ML110 G6 using Ubuntu Linux 10.04 LTS. I have two Digium TE121 single T1 port cards and a Digium AEX800 8-port FXS card. All PCI Express cards. Co-workers are hearing hissing sounds on some calls, and I am getting IRQ errors when running "dahdi show status". I see that sharing IRQs for Digium cards isn't