similar to: "Real" API for Perl?

And the firewall is in between the phones and both servers or are you registering the phones on a local server and trunking to the other server through the firewall? In terms of nat and Cisco 7960s I've never had a issue registering two of them behind nat to a server on the other side, however, if you called one phone from the other, you'd end up with one way audio. -----Original

<asterisk-users at lists.digium.com> Subject : Re: [asterisk-users] Multiple SIP phones behind a Linksys firewall Date : Sat, 2 Feb 2008 18:25:16 -0700 > And the firewall is in between the phones and both servers or are you registering the phones on a local server and trunking to the other server through the firewall? > > In terms of nat and Cisco 7960s I've never had a

Hi folks. Please don't flame me but I've been googling around for days, read a tremendous amount, tried everything, and still no go. This is most definitely a typical newbie question. - I sure hope there's somebody(s) out there who'll humble themselves to help me out. I've set up an 'out of the box' basic Asterisk server running on Slackware Linux. - It basically

Ok, I have spent all night trying to figure this out, and hopefully somebody has a similar experience. I have a very basic asterisk config. Sample configs, with the only addition being by SIP phone, and my incoming voip. Last week I got everything setup, calls were working, etc.,. I cam across a tutorial for voicemail, followed it, and it worked. When I call my phone and dont answer, it goes

I just bought two new Linksys WRT54G routers. Sveasoft has loaded Linux on this router and included a bunch of Linux tools, one of which is Bandwidth Management. The QoS aspect of this is supposed to be much more granular than the previous solution (Wonder Shaper). I have not been able to find any suggestions for how to impliment QoS (Bandwidth Management) using the web interface of Alchemy.

Hi all, We have put together a firmware for a range of inexpensive routers. It has been configured to provide optimum VoIP performance. We have internally tested it for number of months and it looks very good. You should be able to run it easily with 20+ phones on local network ( we still did not hit the upper limit ) assuming that you have bandwidth. Your VoIP will get prioritized over other

Hello, Let me first start by saying Shorewall is awesome, and I use it everywhere from single box firewall, to home network firewall, even to our corporate firewall. I am experiencing a problem getting my home firewall to work with my BroadVoice VoIP connection. I use the Sipura SPA-2100 ATA (Analog Telephone Adapter) that came with my BroadVoice account. This happened when I tried to replace

Hi all, Any one tried installing Asterisk on Linksys WRT54G? We have but facing problems with SIP to SIP calls. The phones ring and calls are established but we cannot hear any voice at all. I tried allow=all in the general section but did not work. So I forced ulaw. Can any one please check it out and let me know what is wrong? Here are the conf files: Asterisk Version: Asterisk

Hello to everybody, does anybody knows how to install Asterisk on a Linksys WRT54G(S)? I had read in the Wiki that it is possible. If somebody has a tip, this would help me very much. Regards Bastian

Hi, I've just installed asterisk 1.2.1 on my openwrt distro ( I own a WRT54GL by Linksys ) . No problem by now, but I can see that my 3 snom 320, once they started they send subscriptions to asterisk, and I can see that running: sip show subscriptions But, after one hour about, OR when I do asterisk reload , asterisk losts all th snom subscriptions. Someone can help me please? Thanks

Hi, I'm stuck doing an install with Polycoms at a small office with no RJ-45. They went wireless 100%, poor them. I insist on using Polycom unless it's impossible because that's what I am standardized on for many reasons. What's the best way/device to turn a wired Polycom 501 (or any Polycom for that matter) into a WiFi phone? Mike -------------- next part --------------

Hi, I'm trying to configure Sipura 2000 (behind NAT) which connects to Asterisk (public IP, no NAT) and having interesting results. When Sipura is behind Linux/NAT firewall it works great and no special NAT settings on Sipura are necessary. The issue I'm having is when Sipura is behind Linksys broadband NAT router. Sipura gets registered with Asterisk just fine, but I can't hear

Did anyone see the article? It''s the first time I really noticed that these little Linksys routers are such a fully fledged linux machine with a decent processor and a replacable firmware. I am now itching to get one to replace the multipurpose firewall desktop machine. Has anyone experimented with the current state of the firmware and how advanced you can get with tc rules? For

current setup SIP phone 192.168.1.30 --> linksys wrt54g sveasoft -- INTERNET -- (xl0) Firewall (xl2:172.16.0.50)--> (em1:172.16.0.101) Asterisk problem is RTP stream not oging trouhg from * to sip and vice versa. #1 and asterusk is pushing 192.168.1.30 back to linksys with 172 as return address.... or #2 asterisk trying to get back to me as 192.168 on public internet.. got

Hello all, I have my * server setup behind a Linksys WRT54G on Adelphia cable. I have forwarded 5060,10000-10020, and another port set can't remember off the top of my head but I can't seem to connect to the * server from any locations that are direct connects to the Internet. Am I missing a portset for forwarding? If I use the name service (voip.*****.com) from my home connection on the

Ok, I've done some more research and I don't think I want an FXO box... What I'd like to do is use BroadVoice (with their BYOD plan) and then run Asterisk on my WRT54G router. I'd also like to use my regular home phones without having to use a special "SIP" phone... (eg. I like my Vtech normal cordless phones) What do I need to buy to get this working? It sounds like I

Hello All, I would be grateful for some help with this issue. I have gotten Asterisk to work with Broadvoice on outgoing calls only. When I try to call my Broadvoice number from another location I get a caller is busy message. My Asterisk box is behind a Linksys WRT54G. Could this be the problem? On the Linksys, I have port 5060 forwarded to the asterisk box 192.168.1.2. I have tried not

Hi, We're installing an * box next week (pbxtra from fonality) and I'm trying to come up with a solution for remote users that want a phone in their home. I need VPN and QoS capability, wireless support would be a nice to have. Ethernet handoff is fine, i don't need integrated dsl or cable modem... I've been googling and cruising the list and can find bits and pieces

I'm trying to setup Asterisk on my Linksys WRT54G router and it appears to startup successfully (no errors) and it says it is listening on 0.0.0.0 port 5060, but I am unable to connect to it. I've tried "telnet localhost 5060" but it just says connection refused. I've also tried connecting from another machine on my network (eg. telnet 192.168.0.1 5060) but it also says

Hello, Did anyone succeeded in installing Asterisk on OpenWRT system. pls help. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090724/aee7ee12/attachment.htm