similar to: Astersik Transcoder support

Hi, Sometimes, you need to send requests to SIP phones either from Linux command line or from Asterisk dialplan. Which is the most efficient way to know a SIP phone IP address ? Today, I think I would use : asterisk -rx "sip show peer 692" | grep "Addr->IP" | awk '{print $3}' I'm wondering if anything more concise and efficient exists ? Regards --------------

Hi All, I have recently installed a TC400B card into a system and am trying to get it to work. As far as I ca tell from the docco on Digiums website, there is no config as such unless you want to enable / disable only 1 codec, otherwise by default it runs as 92 channels of either. I have tried asterisk 1.4.9, 1.4.10 and 1.4.10.1 along with zaptel 1.4.4 and addons 1.4.2. The zaptel modules

Dears Any one knows a standalone voip transcoder software name,not an ip pbx. What I want is to transcode the incoming sip calls from g711 to g723 or ilbc or g729 ..... and forward it to a media gateway .. Regards Khaled chehab ********************************************* No employee or agent is authorized to conclude any binding agreement on behalf of Xplorium with another party by

Hi Im trying to install my TC400B trans coder card when I do: modprobe wctc4xxp tail -f /var/log/messages says: May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Encoder' with 92 transcoders (srcs=0000000c, dsts=00000101) May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Decoder' with 92 transcoders (srcs=00000101, dsts=0000000c) May 13 14:56:36 pbx2

Hello all, I have a TC400B Digium card in order to deal with transcoding and I have some trouble using it, I have a timer synchronisation problem! I would be very grateful if you have any idea to help me? It seems that the card is not correctly synchronised to the system because when I speak to one side, the sound takes 5 seconds to go to the other side, and increasing, after 30 seconds of call,

I've downloaded: asterisk-1.4.1 zaptel-1.4.0 I've compiled and installed zaptel. When I go to install asterisk I do: ./configure make menuselect I then take a look under the codec selection menu and I see that codec_zap can not be compiled. *************************************

hi folks. i have several remote sites with total of 200 sip phones connect to our Asterisk server. i want to minimize bandwidth usage and thinking about getting a Digium TC400B transcoder card. what are your experience with it? how's the quality? also if there are 120 active channels in used. will the 121 person able to make calls? will it support more channels if i put 2 cards in the system?

Good afternoon, I'm trying to use the CLI command file convert on an Asterisk 1.4.26 server with a TC400B transcoding card. The transcoding card is working well for calls but I have some trouble converting sound files from alaw to g729. The command creates empty file as you can see below... CLI> file convert /var/lib/asterisk/sounds/fr/service_notactivated.alaw

Dear all I have one more question about codec what codec i use for LAN setup G.729 or Alaw which is best for LAN setup caz some people told me G.729 is use for wan link not for lan caz it is cost effective so can anyone suggest me best codec for asterisk and SIP phone Rgds satish patel --------------------------------- Don't pick lemons. See all the new 2007 cars at

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Greetings, Because of the heavy load and the high expectations of an asterisk server offered as a solution integrated with our CRM software.. we were looking into other possibilities than software Licenses for G729 and G723 codecs.. to lower the pressure on the processor giving it more space to do more work. We heard of a hardware (PCI CARDS) can be used with Asterisk that does the work. And we

HI; Thanks for your reply. The reason for why I am going through asterisk in such case is just "using asterisk voicemail service" I mean: ATA1 calls ATA2, suppose ATA2 is unreachable or he is not at the office, then the call reroute (my GK is able to reroute calls if the first route is not valid) to atersik for voicemail service. Do you think I can handle it with asterisk native

Slash-dot is pointing to this article on Asterisk and Pingtel. http://www.theregister.co.uk/2005/05/22/pingtel_voip/ Paul Paul Mahler www.signate.com

Hello, I am writing a program based on Astersik Manager which needs to put calls on hold and to redirect them to others extensions. I haven't funded any action able to do this. Is there a way to place calls on hold using Asterisk Manager Actions? Amaury -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hey Guys, I've been working on Icecast 2.3.1 on my test server (Virtual Server-win2k3) And I am not able to get either stream transcoder v3 or v1.25/6 (whatever the current dos one is) to work on it. Also, there is a problem with the people from the game secondlife, they also cannot connect to the server to listen to it. Has something changed in the latest configuration? I've gone

Hi All, Should anyone be looking for one, here's a DirectShow-based command-line transcoder for Theora: http://www.eddiana.com/?totheora.html It can do basic video transcoding, as well as scale video, watermark video with a graphic, grab frame stills, capture from video sources, and perform a couple color transformations. Ed

-----Original Message----- From: MAKRO BAGAFORO, Melvin Sent: Friday, November 16, 2001 11:52 AM To: 'Ben Elliston' Subject: RE: samba error Hi Guys, I already downloaded the latest config.guess and config.sub files, './configure' command is now error free. However, I have another problem, samba won't start. Samba test results:

Hi to all!! I'm successful to connect Asterisk to PostgreSQL database... If it's possible, can anyone learn me how to store sip user in PostgreSQL database and how to configure voicemail?? Thanks for all!!!

Dear Sirs, I had compiled PWlib and OpenH323 correctly in my Fedora Core 2. But when I try to compile asterisk-oh323 I get the following error: `__use_AST_MUTEX_DEFINE_STATIC_rather_than_AST_MUTEX_INITIALIZER__' How can I solve it? Thank you for your help. Juanjo

Hi, I am new to the Asterisk world. I don't know much about the architecture, but I am involved in installing and configuring the VoIP system. My requirement is to build a VoIP system using the 4 input lines (ISDN up0 telephone lines), it must be possible to receive calls from outside through the 4 ISDN up0 input lines, and also possible for outgoing calls, conferencing .etc. I