similar to: Unicall

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi all, Anyone have an idea which version of spandsp, libunicall, libmfcr2, libsupertone, app_rxfax/app_txfax and chan_unicall I should use for the latest asterisk 1.2? Would that be the ones listed below? http://www.soft-switch.org/downloads/spandsp/spandsp-0.0.4pre4.tgz http://www.soft-switch.org/downloads/snapshots/spandsp/test-apps-asterisk-1.2/

If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN

Dears, After having set up the board Digium TE420 to receive 3 E1s, I can receive calls without difficulties. As you can see in the log below: -- Executing [5908 at from-pstn:1] NoOp("UniCall/14-1", "Catch-All DID Match - Found 5908 - You probably want a DID for this.") in new stack -- Executing [5908 at from-pstn:2] Goto("UniCall/14-1",

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hello All, Does anyone know of a software emulator that can be used to simulate hardware such as an E1? I need to play with AstUnicall in a test environment and don't have access to these circuits from the US. If there is an alternate way to test/play with AstUnicall, please let me know! Thanks, Mark -------------- next part -------------- An HTML attachment was scrubbed...

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Hello there! I've problem with setting up unicall / mfcR2. can't find proper notation for channel, trying unicall/1, unicall/1/1001, unicall/g1, unicall/g1/1000 and still having no luck. klaudia*CLI> !cp call /var/spool/asterisk/outgoing -- Attempting call on Unicall/1001 for application Dial(363) (Retry 1) Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:

Hi Moy, Bottom line up front (yes I'm military):How do I now configure some of my spans as normal Euro ISDN and a few with R2? Do I use a combination of /etc/asterisk/unicall.conf and /etc/zaptel.conf or just unicall.conf for everything? See below for the rest of the details and thanks in advance for advice! I downloaded your astunical-1.4.16 and have been studying it. I have a machine

---------- Forwarded message ---------- From: Brian Hutchinson <b.hutchman at gmail.com> Date: Fri, 11 Jan 2008 12:22:09 -0500 Subject: Trying to build MFC/R2 Hi Moy, I downloaded your astunical-1.4.16 and have been studying it. I have a machine running the latest download of asterisk-1.4-17 and was trying to figure out how to build MFC/R2 support into it. I merged your unicall specific

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

I don?t know if the last message was with content. So, I sent again. I have installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s all right but I can?t make and receive calls. I?m using asterisk 2.1 with the patch made by Jos? P. Leit?o and the follow libs: libsupertone-0.0.2 libunicall-0.0.3 libmfcr2-0.0.3 zaptel 2.1 My number is 34318300. The Telco send me only 8300.

Hi, I have successfully installed libunicall and mfcr2 in Venezuelan variant. We are able to receive, make calls without any problems. When we place a call from a snom sip phone through chan_unicall and press a dtmf (either using info, rfc2833 or inband) Asterisk seems to get the order of playing dtmf but a garbage is heard at the other side. I have been trying to narrow down the problem on

Hi Asterisk-user, Steve; I?m using "*libmfcr2-0.0.3.tar.gz, libsupertone-0.0.2.tar.gz, libunicall-0.0.3.tar.gz,spandsp-0.0.3pre22.tgz*" with Fedora core 6 ,Asterisk 1.2.14, libpri 1.2.4 , zaptel 1.2.20; So everything is working perfectly with MFCR2, but sometimes i have problems with MultiFrame Alignment Signal (MFAS),i?m using standard G.732..I would like to Know, where can i

---------- Forwarded message ---------- From: Juan Carlos Huerta <juancarloshuerta at gmail.com> Date: 07-abr-2009 13:41 Subject: Re: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands? To: asterisk-r2 at lists.digium.com Please wirte to asterisk-users at lists.digium.com to get help about this problem. Juan Carlos ~ Lo que no te mata te fortalece ~ On Tue, Apr 7,

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no