similar to: Asterisk mem leak behavior?

I'm scoping out HA for a relatively simple Office/Call Center PBX. Current setup uses a TE412P with 4 PRI our telco with SIP hard/soft phones for users. Some outbound also goes to a SIP provider. Active/Active looks to be too much hassle for an installation this size, so we're looking at adding an extra * in an active/passive configuration with Linux-HA in between them. Does anyone

Has anyone on the list used a Soekris engineering PC as a TDM - Ethernet bridge? For example something like a net4801 with a TE110p in it and then using TDMoE to get it into a bigger server where the call processing proper will occur. Anyone know if it might handle a quadspan card ok? (no transcoding, just pure PRI to TDMoE bridging). Craig

Hello List Does anybody have any experience with the FoneBridge line of products from RedFone? I think their HA implementation sounds interesting, and like the prospect of having dedicated hardware for our PRI connections. Kind Regards Jon Leren Sch?pzinsky

Has anyone every attempted to set up a mini PC to achieve much the same functionality as the fonebridge box? The sort of thing I'm imagining is a micro itx board & case in a completely solid state configuration (flash disk, maybe a psu fan but only if really required), with a TE210P (or equiv) card(s). The sole purpose of this would be to be a bridge between E1 lines and TDMoE. The

Hey guys, I am trying to diagnose a hum in my FXO lines I am using an Adtran 750 with 8 FXO ports. I am getting a pretty bad hum on the line during a call. I have checked the Telco side of the 66 block and there is no hum there so it's my problem to fix. I have tried to lower the gain but that reduces the call volume to much. Where else should I be looking? Setup as follows Dell

I am looking for input on wether the 4 port T-1 foneBridge is a useful device in a asterisk deployment. Would it be better to loadup a extra asterisk server to trunk the T-1's via IAX or is TDMoE safe in production enviroments. We are only looking at 2 T-1's, one for pstn and the other to a channel bank. Any advice? Bruce Reeves Nortex Networks -------------- next part -------------- An

First, Something seems to be wrong with the list. I'm not the only person who has expressed seeing their messages either arrive late, or not at all. With that out of the way.. Is anyone aware of any type of failover device for PRI on asterisk? I've found the ISDNGuard, however it is currently not made in the U.S., nor does it run on U.S. power. Is anyone aware of a device that will

Hi, Some help with dimensioning the server will be gladly accepted. -50 sip phones (g729) or g711(to avoid transcoding) in LAN -an asterisk server (1.4) doing normal pbx functions + voicemail in the same LAN -Some sporadic conferencing with no more than 2 sip phones and maybe 2 or 3 calls coming from the E1 for a total of 5 people in a conference. The asterisk server will get an E1(pri) via one

Does anyone know of a hardware adapter that can take ISDN BRI frames (I.430) and encapsulate them in Ethernet (any form, but TDMoE would be really cool), in much the same way that the redfone does for PRI? (yes I have asked this before in looser terms, but it was a while ago :) Would anyone find such a device useful? Thanks James

Hi List, I'm finding a solution to provide failover and load balancing features to my IVR system. Anyone suggest me what is the best solution please?. what the hardware I should use ?. I heard about RedFone, but someone on the mail list said that it is not good because TDMoE module in asterisk is not so stable and TDMoE is stale. And It seems that RedFone doesn't not support load

Robert, > Is there a product to simulate a PRI trunk? (Robert > Goodyear) TDMoE emulates a T1. ;) Once the TDMoE link is up, Asterisk just sees 24-lines that appear to be a T1 instead of having to deal with all of the complexities of VoIP. This is useful, since probably 75% of the utility of VoIP is really just the fact that it can run over a network. It's also handy because it

I've been asked to look at deploying Asterisk in a high availability environment and I've been looking so I've been searching for methods to decouple the voice PRI circuits from the Asterisk server so failover to another server could take place. I've been looking at the RedFone foneBRIDGE2 2e1 product here:

I'm looking for reports of recent experience with redfone fonebridge2 (with echo can) TDMoE gizmos. Anybody? Good? Bad? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080609/23aeddd6/attachment.htm -------------- next part -------------- A non-text attachment was scrubbed... Name: smime.p7s

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Hello, I want to create channel bank in this case: "channel bank" |-----------------------------------------| | FXS,FXO<----->TDMoE<--|---------------------------------->Asterisk |-----------------------------------------| How can it?

Hi, I'm wondering what the best option to obtain a high availability asterisk server is. I currently use a TE410P (4 x E1) card. I'm thinking of 2 different solutions: - 2 servers configured with Heartbeat + DRBD (drbd mainly for voicemail....) and the E1 span plugged to the 2 servers (with a TE410P in each server). - 2 servers configures with Heartbeat + DRBD with the E1 span hooked

We have been running around than 40 asterisk servers running on Debian Squeeze for last three years, handling traffic of more than few hundred thousand calls per day. Our setup's PRI-banks were using Redfone's Fonebridge. We had PRIs from multiple telephony providers. And Redfone's Fonebridge handled all that easily. But all good things come to end. Redfone's Fonebridge was not

Was'nt sure if this mail got through earlier: I have been having a weird issue with my telco's ISDN PRI occasionally resetting on a incoming call, i suspect it to possibly be a timing issue since some of the incoming call work. This problem happens very frequently. I am using asterisk-1.6.0.1 with libpri-1.4.9, the asterisk server is connected viw TDMoE to a Redfone Fonebridge into

Hello, I am trying to Bridge 2 E1 interfaces over a long distance link exactly the same way Redfone does. How can asterisk be configured to do that? Best regards Arinze Izukanne ___________________________________________________________ Want ideas for reducing your carbon footprint? Visit Yahoo! For Good http://uk.promotions.yahoo.com/forgood/environment.html -------------- next

Hello Out of curiosity, has someone managed to run Asterisk on a Beagleboard for home-use? www.beagleboard.org As an alternative to a PC, it can be powered from a USB hub, so that would make for a compact, fanless Asterisk server. Thank you.