similar to: SPA3000 -- PSTN to VoIP

Hi, all I am building a new server. Have installed FC 6 and put in TDM400 card. Checked out latest asteriusk code, run make install in zaptel directory. So far all is fine. Now I am trying to install the drivers. # modprobe zaptel FATAL: Module zaptel not found. Fair enough, no zaptel driver is found on the system. Is there are any known problems with FC6? I did not have much trouble running

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

Hi, all Stupid question, but how do you exit asterisk console without stopping the asterisk? Tried quit and exit: *CLI> exit No such command 'exit' (type 'help' for help) *CLI> quit No such command 'quit' (type 'help' for help) *CLI> Any other ideas? I started asterisk with -cvvvvg option. Same problem if use asterisk -r to connect. Can not exit. Any

Hi, all I am still battling to connect * and voipbuster. What protocol does it use? Ethereal capture shows UDP traffic, but no SIP or IAX traffic when using their client. VoipBuster client connects to connectionserver.voipbuster.com on port 11112 for authentication. Call itself is placed on different server. I have tried to connect using SIP and IAX and it seems that no authentication is

Hi I seem to have installed the G729 codec properly but can't seem to get it to work .. in the Asterisk startup I see .. [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) == Detected 1 licensed G.729 transcoders WARNING[1074408160]: File translate.c, Line 218 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator

Hi list, After failing to get a Sipura/Linksys SPA3000, which I've configured as a PSTN gateway, to pass on the Caller ID, I decided to try my luck with a Linksys SPA3102 after hearing some promising stories. Unfortunately, I've run into a completely new problem: it seems Asterisk won't let this device register. I went about configuring the SPA3102 in much the same way as I

Hi, all I am reallty pissed with their service. I wonder if this is common problem. Firstly, all of my calls are terminated after 30s. And termination happens in a strange way. My local asterisk server does not see the disconnection, but remote party is disconnected. Basically, I am still on the phone, while remote party was disconnected. When I hang up, I get something like that: Apr 20

Hi, all I am doing "prrof of concept" system. I will have two IP phones connected to Asterisk box. Box itself will have 1 PSTN conenction and one analog phone conenction. A basic minimal configuration. At the moment I am planning to use an old PII-350 with 128M of RAM I have lying around. I can not test anything yet, as I am waiting for phones to arrive, so question is will that be

Hi, These days I run into something quite odd. I have an A@H that was modified to meet our requirements. We have a completely funtional DISA which we use pretty much all the time. I works flawlessly with incomming SIP calls from several providers, IAX calls from FWD and with ZAP. Recently we came out with a situation where it doesn't work... with a

Hi, all I am in Australia and I have to setup Asterisk in few offices. There will be IP phones in each office and I must be able to call between offices. I need actual handsets. I need "standard" handsets to be used by people. Those must support features like CID, call forward, etc. --- your normal office feature set. Also I need some sort of more complex handset to be used by

I'm trying to get working a spa3000 with asterisk. My problem is I cant get wroking the incomming calls (I installed the lastest firmware). My problem is asterisk is rejecting the authentication from the spa3000. Asterisk answers forbidden (SIP/2.0 403 Forbidden) and I think I placed the username and password correctly... Sip.conf says this: [linea2] username=linea2 type=peer secret=1111

Hi, all I want voicemails to be delivered to recepients by e-mail. I have set up voicenail, and I can see asterisk is using sendmail to send messages out. Using Ethereal, I can see that messages are leaving my network, but receipeint mail server never replies back. As a result, mail delivery is timed out. I got a book on sendmail and it looks quite complex. It will take quite a bit of time

Hi, all Can someone tell me where to tell asterisk no to use 127.0.0.1 IP (localhost)? When I am registering with VoIP providers, they get my info as s@127.0.0.1. (This is SIP registration). Also, in SIP logs, when calling I am getting things like this: Executing SetCallerID("SIP/phone2-22c3", ""CID Name" <CIDNUMBER>") > in new stack > -- Executing

hello i am using asterisk-1.0.9. i have a NAT problem. without NAT registration is ok. and if user is bhind NAT it is registring on asterisk. but SJPhone is showing "not registered". i think asterisk is properly sending request to UA. any comments............this sip.conf setting was working previously -- Registered SIP '5000' at 0.0.0.0 port 5060 expires 120 -- Saved

Hi, all A quick question. I have SPA3000 and trying to get call waiting to work. I do receive call waiting tone, however hook flash does not seem to work. I think, I set up SPA3000 correctly. Basically, doing HF 2 (switching calls in Australia) does not do anything. Is there any examples on how to setup hook flash operation in Asterisk? Thanks, Rudolf

Hi list, After successfully configuring Linksys SPA3000 and SPA3102 devices as Asterisk PSTN gateways, the only thing I can't get working is the PSTN Caller ID. The analog and SIP phones I've used can both display CIDs for internal calls, while the analog model also displays CIDs correctly when attached directly to the PSTN line. However, when PSTN calls come in via the SPA

Hi, all I have couple of SIP phones and they are in [from-sip] context. I also have an IAX2 phone. I have put this one in [iax-user] context. I want to make calls between SIP and IAX2 phones. If I put them all in same context all is fine, however when they are in different contexts they will not call each other and I will get message (in * CLI) that particular extension does not exist in a

Lukasz Sokol wrote: > but have you considered a web-managed config-builder such as FreePBX? > Instead of building your dialplan from scratch ? I've never used FreePBX, but, after having looked at its website, I think I have a general understanding of what it can do. What I don't understand is how FreePBX answers my question about the Linksys SPA3102 being good for a mission

I have a number of Polycom phones to setup with my * server. For my initial few phones I hand wrote configs. Does anyone here who uses Polycom phones have some form of management utility for automating their setup? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

G'Day All, Can anyone give me some direction in setting up the TFTP server on my RadHat ES3 box? I did quite a bit of reading, but I think I am more unsure now than before. I found the information nebulous. TFTP is already installed. I am trying to determine where the root directory for the tftp services is located so I can copy the CISCO 7960 firmware files onto it. Thanks.... Ferg