similar to: MGCP Thomson, "early" transmit problem

Hello, After reading all the docs and going through the menus, I still can't find the voicemail access button or menu sequence on the ST2030 (http://www.voip-info.org/wiki/view/Thomson+ST2030) Also I can't get phone provisionning through tftp to work. Configuration files are loaded but the phone seems to ignore them. Any idea?

Hi all, i'm trouble with codec setup on an asterisk machine 1.4.18 and some Thomson ST2030 as extensions. In the users.conf file for internal extension i have: disallow=all allow=g729 allow=alaw allow=ulaw Without any codec installed (i mean with original g729 of asterisk) all go fine, calling from an extension to one other: Peer User/ANR Call ID Seq (Tx/Rx) Format

hi there, I saw a page on voip-info about the thomson ST2030 phone. There is not so much info on there, that's why I would like to raise a question here. Has anyone got hands-on experience with this phone? (with or without extension module) I am interested if it can be used (as SIP phone) in a good way with asterisk. (also, do all the functions behave like they should; like Supervision

Hello, I'm trying to upgrade a Thomson ST2030 phone froms its default 1.42 firmware to the latest version (1.56) through tftp. The phone loads the .inf file, then the correct firmware file (as stated in the ST2030S.inf), then it reboots and loops doing these same things again and again. The firmware version on the phone stays at 1.42. Is there a special intermediate firmware version to

Hello. Once again, I came up with a problem for which I can't seem to find a solution. I'm not able to make BLF work with Thomson ST2030 phones and Asterisk (1.2.13). I've set up hints in dialplan, as well as Subscibe keys on the phone. The LED status gets updated according to the associated line status. However, when a phone is ringing, If I try to pickup the call by pressing the

Hi! I wish you all e Happy New Year first! Allthough, I'm relative new to Asterisk, I got our server up and Running, Softphones, ISDN, and a brand new Snom 821 are working flawlessly. :) Platform is Debian 8/Asterisk Packages (11) from Debian Repo. But I am running into problems setting up 2 older Hardphones, Thomson 2030S. :( with in my sip.conf, I have got for this hardphone: [...]

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

Hello, I try to place a call between CISCO IP phone 7905 (h323) and an analogue telephone on DLINK DG-104S (mgcp). Call setup is handled ok - both way, but after connection of the call I get both site no-audio, even codec are Set to alow-64 both. The call is terminated with this debug output - Didn't get a frame from channel: MGCP/aaln/1@dlink-1 and is Hanged up. Jan 18 20:32:55

ONLY ON MONDAY! Well it used to work - calls between my aaln's that is. I moved from debain to redhat (same conf. files for asterisk) and this is what I get.. looks like several errors. errors I never got before. Also asterisk isn't observing the digits as I dial them like it used to however it still trys to route the call when I'm finished dialing. Anyone with a though on this?

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Ishfaq Malik <ish at pack-net.co.uk> schrieb: > Do you have a link to the user guide for your exact phone model? Unfortunately not... I have a Thomson ST2022, but I can just find in Internet manual for the ST2030... Regards Luca Bertoncello (lucabert at lucabert.de)