similar to: inbound Audio problems probably not NAT related?

I am looking for pros and cons on the Intel Atom cpu. Has anybody been using these in production? I am looking at an Atom D510 (dual core 1.6GHz, 1M cache) to run maybe 25 to 30 extensions, 4 or 5 calls at once(maybe as high as 7 simultaneous calls), g729 all the way through except voicemail will be wav format for email purposes(requirement). I will be tying 3 of these together to route

Dear All, I have my puppet servers and clients on puppet 2.7.20 and I am planning to upgrade to the latest version. But the problem is that I have a lot of modules (downloaded from forge and few of my own) which used by hundreds of puppet clients. I need to know 1) Will the functionality of these modules get affected after this upgrade ? 2) Other than ritual of being on the latest verison, are

When does echo 0 > /selinux/inforce need to be used? I.e., where is selinux enforcing itself on the system to protect it? When I do yum install of some package, it seems to work (not being blocked). When would doing something not work because selinux is watching it (or whatever that process is doing)? Thanks, -wes

I've been racking my brain for the last two days to try to figure out what I could possibly be doing wrong in my configuration for a SIP trunk that's setup through my local ISPs Metaswitch. I've setup a very simple SIP Peer, which I've played around with a lot in the past two days but still comes back to the following basic setup: [provider-fireball] type=friend

On NetBSD 6.99.28-CURRENT, nsd 3.2.16 works fine, however nsd 4.0.0 is spinning chewing CPU. The logs show: Nov 28 23:07:00 xxx nsd[466]: sendmmsg failed: Resource temporarily unavailable ktruss shows it getting EAGAIN from sendmmsg(2) over and over again. According to the man page: [EAGAIN|EWOULDBLOCK] The socket is marked non-blocking and the requested

Hello, I searched the archives mailing list of LARTC. Everyone discussed about marking outbound ftp traffic . I could not find any thread discussed about marking inbound ftp traffic. With inbound ftp traffic , we don''t know the random ports specified by ftp servers in passive mode ? So marking inbound ftp traffic is impossible ? If it is possible, can you tell me, Thanks in

Hi, I am using the following script to limit my outbound traffic. This scipt runs on a box behind my firewall. It limits my outbound passive ftp traffic to 39K perfectly....just like i want. However, i just noticed that it is also limiting uploads coming to my server. Is there something I can change to make it not limit uploads to my server? #!/bin/bash #shaping passive ftp traffic #

I have 3 ISP (I tried also with only two ISP) and I would split inbound traffic over all 3 real ip address (one per ISP). All 3 external ip are forwarded to an internal web server. I ''ve done all specified in the LARTC howto (4.2.1), but my firewall/router works fine only: 1. when I access from internet to the ip which is on the same interface of default gateway; 2. when I access

Guys, How would you block inbound call's? for example person who is calling me is 212-555-1212, and I would like to do not receive the calls from this person and give them busy tone. What should I write in asterisk config files? and in to witch file should I write it??? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Everyone, I have a SIP turnk which works fine with both inbound and outbound calling. However, the only issue is that there is no Ring Tone if someone calls us. The phones used are Aastra and Polycom connected to the PBX via VPN (SIP). I do get an outbound ring tone, so it's not that there is any media loss between the phones and the PBX. But when the DID is called there is dead silence

Hi All Can anybody help me for dial plan which can barge inbound call groupwise. Because when i am trying to barge inbound calls which is coming on my DID number i can hear 1st 3 digit of my Inbound provider IP address instaed of extension which pick that calls. I tried Chanspy as well as Extenspy. But result is same. So Plz Help me. Thanks Amit -------------- next part --------------

A virus has been detected in a message addressed to helpdesk.aberdeen at cnrinternational.com from r-help at lists.r-project.org. The subject of the message is Re: Here. The virus could not be cleaned and the message is held in Dirty Messages Message from: r-help at lists.r-project.org. Message subject: Re: Here Sent to: helpdesk.aberdeen at cnrinternational.com Dated: Sun, 14 Nov 2004

Hi List, Someone may have run into this problem. Very strange. I have a customer running 1.422. They use a digium ISDN card connected to an primary rate for their inbound currently. We have tested inbound SIP from one of our trunks. We use these trunks with all our asterisk customers without an issue. With this Asterisk box when we answer an inbound SIP call to an extension literally after .5

Greetings list- I have a box with a single FXO card in it. I'm able to dial out ZAP/1 with no problems and as expected. However, I would like inbound calls on that POTS line to go unanswered by Asterisk since I have other equipment on the line. I've setup zapata.conf for the channel without a context but the line is still answered. I've also setup a blank context with the same result.

Hello all. I have installed AsteriskNow 1.7.1-64bits with freePBX. The system has 1 DAHDi card with 2 analog FXO ports (to pstn) and 1 FXS port connected to a FAX machine. I want the every call received on port FXO-2 to be redirected to the FAX machine. So, what I configured was that every call with DID 12345 (let's suppose that 12345 is the DID connected to the FXO-2)to be redirected to the

Is there a way to specify the outbound leg Call-ID? -- Eric Chamberlain

The Bank of Bermuda's Internet email security system has detected a virus in an inbound email. The details are below: The sender is samba@samba.org The intended recipient(s) is/are pervaim@bankofbermuda.com The subject is SAMBA digest 2418 The security scenario detected is Scenarios/Incoming/Detect Link/SEARCH: The operation completed successfully. Scenarios/Incoming/Detect Worm/SEARCH: The

Hi all, Can anyone help with the logic of which commands to use to say: 1. Extension is 600 2. See if has an ongoing call 3. Check if inbound or outbound to the extension 4. Find callerid of inbound call Been reading http://www.voip-info.org/wiki/view/Asterisk+manager+API Using latest 1.6. Thanks.

The current virtio_net driver has a startup race, which prevents any incoming traffic: If try_fill_recv submits buffers to the host system data might be filled in and an interrupt is sent, before napi_enable finishes. In that case the interrupt will kick skb_recv_done which will then call netif_rx_schedule. netif_rx_schedule checks, if NAPI_STATE_SCHED is set - which is not as we did not run

The current virtio_net driver has a startup race, which prevents any incoming traffic: If try_fill_recv submits buffers to the host system data might be filled in and an interrupt is sent, before napi_enable finishes. In that case the interrupt will kick skb_recv_done which will then call netif_rx_schedule. netif_rx_schedule checks, if NAPI_STATE_SCHED is set - which is not as we did not run